| CP45错误信息报告中英文 |
| $0001 <$E> Emergency switch is pressed. | $0001 <$E> 紧急开关被按下。 |
| $0002 <$E> Front emergency switch is pressed. | $0002 <$E> 前面的紧急开关被按下 |
| $0003 <$E> Rear emergency switch is pressed. | $0003 <$E> 后面的紧急开关被按下。 |
| $0004 <$E> Motor free switch on a teaching box is pressed. | $0004 <$E> 马达开关示教盒被按下。 |
| $0006 <$E> I/O power switch is turned off. | $0006 <$E> 输入／输出电源开关关掉 。 |
| $0007 <$E> I/O power switch cannot be turned on. | $0007 <$E> 输入／输出电源开关不能够打开。 |
| $0008 <$E> JogBox has been disconnected in presence of axis motion. | $0008 <$E> JogBox有在～之前桥提议被分离。 |
| $0010 <$E> Front feeder float sensor activated. | $0010 <$E> 前面喂料器感应器被感应。 |
| $0011 <$E> Rear feeder float sensor activated. | $0011 <$E> 后面喂料器感应器被感应。 |
| $0020 <$E> Front door is open. | $0020 <$E> 前门是开着的。 |
| $0021 <$E> Rear door is open. | $0021 <$E> 后面门是开着的。 |
| $0030 <$E> Front cart was released while the location of the XY gantry was NOT secured. | $0030 <$E> 当XY gantry的位置不被固定的时候,前面手推车被释放。 |
| $0031 <$E> Front cart was released during the disallowed state for the cart releasing. | $0031 <$E> 前面手推车为手推车释放在被不许的州时候被释放。 |
| $0032 <$E> Rear cart was released while the location of the XY gantry was NOT secured. | $0032 <$E> 当 XY gantry 的位置不被固定的时候 , 后面手推车被释放。 |
| $0033 <$E> Rear cart was released during the disallowed state of the cart releasing. | $0033 <$E> 后面手推车在手推车释放的被不许的状态时候被释放。 |
| $0040 <$E> Mirror Safety Sensor Error. | $0040 <$E> MIRROR安全感应器错误。 |
| $0100 <$E> VME Module Ver %d started. | $0100 <$E> VME 组件 Ver%d 开始。 |
| $0102 <$E> PCB Download Start <$W> | $0102 <$E> PCB 数据装载开始 <$W> |
| $0103 <$E> PCB Download End | $0103 <$E> PCB 数据装载结束 |
| $0104 <$E> Vision Module Ver %d started. | $0104 <$E> 视觉组件 Ver%d 开始。 |
| $0110 <$E> Auto Run Start | $0110 <$E> 自动运行开始 |
| $0111 <$E> Auto Run Stop | $0111 <$E> 自动运行停止 |
| $0112 <$E> Auto Run Pause | $0112 <$E> 自动运行中止 |
| $0113 <$E> Auto Run Reset | $0113 <$E> 自动运行复位 |
| $0114 <$E> Auto Dump All Report | $0114 <$E> 自动废料所有记录 |
| $0120 <$E> Feed Change Request | $0120 <$E> 喂料器更改需求 |
| $0800 <$E> $A axis motion is interfered by another axis. | $0800 <$E> $A轴运动时被其它轴。 |
| $0801 <$E> Error occurred while a motion to move to a safe position was taking. | $0801 <$E> 错误发生在一个动作移动到一个安全的位置正在拿。 |
| $0802 <$E> A motion for $A axis is interfered by another axis. | $0802 <$E> 一个提议为 $A一个桥被另外的一个桥妨碍。 |
| $0803 <$E> In a manual operation, %d axis motion is interfered by %d axis. | $0803 <$E> 在手动操作时,%d 轴运动时被%d 轴中断。 |
| $0804 <$E> In a manual operation, %d axis or %d axis motion is interfered by %d axis. | $0804 <$E> 在人工的操作方面,%d 桥或 %d 桥提议被妨碍被 %d 桥。 |
| $0805 <$E> Unable to activate feeders because of the unsecured Z axis position. | $0805 <$E> 不能因为unsecured Z 桥位置刺激饲养者。 |
| $0806 <$E> Safety-speed is NOT normal. | $0806 <$E> 安全-速度不是正常。 |
| $0807 <$E> Manual placement is not allowed while the vaccum is on. | $0807 <$E> Manual placement is not allowed while the vaccum is on. |
| $1000 <$E> H/W Limit in the negative direction was detected in $A axis. | $1000 <$E> 反方向硬限位在$A 轴被检测。 |
| $1001 <$E> H/W Limit in the positive direction was detected in $A axis. | $1001 <$E> 正方向硬限位在$A 轴被检测。 |
| $1002 <$E> ALARM occurred in $A axis. | $1002 <$E> 警报发生在 $A轴。 |
| $1003 <$E> The $A axis failed to stop in a specified time duration. | $1003 <$E> 那$A一个桥无法在被叙述的时间期间内停止。 |
| $1004 <$E> An error was detected in the $A axis. | $1004 <$E> 一个错误被发现在那 $一个桥。 |
| $2000 <$E> Encoder error detected in the conveyor-width adjusting axis. | $2000 <$E> 编码器错误在运送装置- 宽度调整桥中发现。 |
| $2001 <$E> Failed to lift the BUT. | $2001 <$E> BUT上升失败 |
| $2002 <$E> Failed to lower the BUT. | $2002 <$E> BUT下降失败。 |
| $2101 <$E> Failed to advance the Edge Fix. | $2101 <$E> 边定位无法夹紧 |
| $2102 <$E> Failed to step back the Edge Fix. | $2102 <$E> 边定位松开失败。 |
| $2201 <$E> HOLE_FIX_UP_ERROR | $2201 <$E> 孔定位上部感应器感应错误 |
| $2202 <$E> HOLE_FIX_DOWN_ERROR | $2202 <$E> 孔定位下部感应器感应错误 |
| $2210 <$E> Sensor of Hole Fix is not detected. | $2210 <$E> 孔定位感应器没被检测到 |
| $2211 <$E> Rightward sensor of Hole Fix cannot be detected. | $2211 <$E> 右上方孔定位感应器不能检测到 |
| $2212 <$E> Leftward sensor of Hole Fix cannot be detected. | $2212 <$E> 左上方孔定位感应器不能检测到 |
| $2301 <$E> Edge Fix cannot be advanced. | $2301 <$E> 边定位不能升级 |
| $2302 <$E> Edge Fix cannot be stepped back. | $2302 <$E> Edge Fix cannot be stepped back. |
| $2400 <$E> Error detected in adjusting conveyor width. | $2400 <$E> 错误信号被检测在轨道宽度调节中 |
| $3000 <$E> PCB detected in conveyor area. | $3000 <$E> PCB被检测在传送区域 |
| $3001 <$E> PCB detected in PCB-in sensor area. | $3001 <$E> PCB被检测在入口感应处 |
| $3002 <$E> PCB detected in PCB-wait sensor area. | $3002 <$E> PCB被检测在等待感应处 |
| $3003 <$E> PCB detected in PCB-work sensor area. | $3003 <$E> PCB被检测在贴装感应处 |
| $3004 <$E> PCB detected in PCB-out sensor area. | $3004 <$E> PCB被检测在出口感应处 |
| $3010 <$E> Two PCBs detected in the input buffer. | $3010 <$E> 2块PCB被检测在缓冲信号时 |
| $3021 <$E> PCBs detected in the input buffer or the wait buffer. | $3021 <$E> 所有PCB被检测在缓冲信号输入或等待时 |
| $3022 <$E> PCB detected in the placement buffer. | $3022 <$E> PCB被检测在贴装缓冲信号 |
| $3023 <$E> PCB detected in the transmission buffer. | $3023 <$E> PCB被检测在缓冲信号传输中 |
| $3031 <$E> PCB-in sensor is NOT normal. | $3031 <$E> PCB-入口感应处是不正常的 |
| $3032 <$E> PCB-wait sensor is NOT normal. | $3032 <$E> PCB-等待感应处是不正常的 |
| $3033 <$E> PCB-work sensor is NOT normal. | $3033 <$E> PCB-贴装感应处是不正常的 |
| $3034 <$E> PCB-out sensor is NOT normal. | $3034 <$E> PCB-出口感应处是不正常的 |
| $3035 <$E> PCB-work-out sensor is NOT normal. | $3035 <$E> PCB-贴装-出口感应处是不正常的 |
| $3101 <$E> PCB did not arrived at the wait sensor area. | $3101 <$E> PCB没有被感应到在等待感应器处 |
| $3102 <$E> PCB did not arrived at the work sensor area. | $3102 <$E> PCB没有被感应到在贴装感应器处 |
| $3103 <$E> PCB did not arrived at the out sensor area. | $3103 <$E> PCB没有被感应到在出口感应器处 |
| $3104 <$E> Error occurred in transmitting a PCB. | $3104 <$E> 错误产生在PCB传输中 |
| $3201 <$E> Failed to move PCB in the wait sensor area. | $3201 <$E> PCB不能传送在等待感应区 |
| $3202 <$E> Failed to move PCB in the placement sensor area. | $3202 <$E> PCB不能传送在贴装感应区 |
| $3203 <$E> Failed to move PCB in the transmission sensor area. | $3203 <$E> PCB不能传送在传输感应区 |
| $3301 <$E> Wait Stopper cannot be raised. | $3301 <$E> 等待止挡器不能上升 |
| $3302 <$E> Wait Stopper cannot be lowered. | $3302 <$E> 等待止挡器不能下降 |
| $3401 <$E> Work Stopper cannot be raised. | $3401 <$E> 贴装止挡器不能上升 |
| $3402 <$E> Work Stopper cannot be lowered. | $3402 <$E> 贴装止挡器不能下降 |
| $3501 <$E> Out Stopper cannot be raised. | $3501 <$E> 出口止挡器不能上升 |
| $3502 <$E> Out Stopper cannot be lowered. | $3502 <$E> 出口止挡器不能下降 |
| $3600 <$E> AREA_PCB_OVER_MAXIMUM_WARNING | $3600 <$E> PCB范围超值报敬 |
| $3601 <$E> MOUNTING_OVER_MAXIMUM_WARNING | $3601 <$E> 贴装范围超出最大值报警 |
| $3700 <$E> SMEMA_SIGNAL_TIMEOUT_ERROR | $3700 <$E> 连机信号延时报警 |
| $3701 <$E> TimeOut error occurred in Conveyor during operation. | $3701 <$E> 延时错误发生在轨道运行中 |
| $3fff <$E> CONV_NOT_DEFINED | $3fff <$E> CONV_NOT_DEFINED |
| $4000 <$E> Parts exist that cannot be operated in same cycle. | $4000 <$E> 元件不能被操作在同一个周期中 |
| $4001 <$E> Error occurred during manual operation. | $4001 <$E> 错误发生在手动操作过程中 |
| $4002 <$E> Attempted to use undefined Operation Mode. | $4002 <$E> 尝试使用未定义的操作模块 |
| $4004 <$E> Invalid bad mark position finding method. | $4004 <$E> 无效的坏标志位置检测方式 |
| $4005 <$E> Invalid door type. | $4005 <$E> 无效的门检测类型 |
| $4110 <$E> TOO_MANY_DUMP | $4110 <$E> 废料太高 |
| $4111 <$E> Dump Conveyor is in ERROR state. | $4111 <$E> Dump Conveyor is in ERROR state. |
| $4112 <$E> Dump Conveyor is in FULL state. | $4112 <$E> Dump Conveyor is in FULL state. |
| $4113 <$E> Dump Conveyor is in BUSY state. | $4113 <$E> Dump Conveyor is in BUSY state. |
| $4115 <$E> A Different kind of Part already exists on the Shuttle Pad. | $4115 <$E> 不同种类的元件已经存在SHUTTLE PAD。 |
| $4116 <$E> Error occurred during the manual Pick operation. | $4116 <$E> 错误发生在手动吸取元件操作中 |
| $4117 <$E> Error occurred during the manual Dump operation. | $4117 <$E> 错误发生在手动丢料操作中 |
| $4200 <$E> Head $H attempted to pick a part, beyond the limit position of %, at %d position. | $4200 <$E> 头$H 试着去拾取一个元件,超过极限位置的 %d,在 %d 放置。 |
| $4201 <$E> Head $H attempted to place a part, beyond the limit position of %, at %d position. | $4201 <$E> 头$H 试着贴装一个元件,超过极限位置的 %d,在 %d 放置。 |
| $4202 <$E> Head $H attempted to change a nozzle, beyond the limit position of %, at %d position. | $4202 <$E> 头$H 试着换嘴,超过极限位置的 %d, 在%d 放置。 |
| $4300 <$E> $A axis reached the (-) S/W Limit using Jog Box. | $4300 <$E> $A轴到达负极限使用JOG BOX |
| $4301 <$E> $A axis reached the (+) S/W Limit using Jog Box. | $4301 <$E> $A轴到达正极限使用JOG BOX |
| $4400 <$E> Side illumination in the head module cannot be raised. | $4400 <$E> 侧边的光在头组件中不能够被升起。 |
| $4401 <$E> Side illumination in the head module cannot be lowered. | $4401 <$E> 侧边的光在头组件中不能够被降低。 |
| $5000 <$E> Invalid feeder type. | $5000 <$E> 无效的FEEDER类型 |
| $5001 <$E> No parts in $F( $P ). | $5001 <$E> 无元件在$F($P) |
| $5002 <$E> Auto Skipped part exists. | $5002 <$E> 自动跳过已有元件 |
| $5003 <$E> Mounting for the user defined number of PCBs was completed. | $5003 <$E> 用户定义的PCB数据贴装完成 |
| $5011 <$E> Vacant slot exists in the feeder base. | $5011 <$E> FEEDER基座上的空位 |
| $5012 <$E> Feeder Type Mismatching. | $5012 <$E> FEEDER类型配置不适合 |
| $5100 <$E> No parts in $F. | $5100 <$E> 没有元件在$F |
| $5101 <$E> $F Head $H $P $N Retry Out | $5101 <$E> $F 头 $H $P $N 再试出 |
| $5200 <$E> No parts in $F. | $5200 <$E> 没有元件在 $F。 |
| $5201 <$E> $F Head $H $P $N Retry Out | $5201 <$E> $F 头 $H $P $N 再试出 |
| $5300 <$E> No parts in $F. | $5300 <$E> 没有元件在 $F。 |
| $5301 <$E> $F Head $H $P $N Retry Out | $5301 <$E> $F 头 $H $P $N 再试出 |
| $5302 <$E> SHUTTLE_MISMATCH_PART | $5302 <$E> SHUTTLE_MISMATCH_PART |
| $5303 <$E> Shuttle Tray Feeder is in Error state. | $5303 <$E> SHUTTLE盘式FEEDER在错误状态。 |
| $5304 <$E> Vacuum Error occurred in C/M. | $5304 <$E> 真空错误发生在C/M |
| $5500 <$E> TRAY_COMM_ERROR | $5500 <$E> TRAY命令错误 |
| $5501 <$E> Tray Feeder(CH %d) is in error state. | $5501 <$E> TRAY FEEDER(CH %d)是错误的状态 |
| $5502 <$E> Tray Feeder(CH %d) is not in ready state. | $5502 <$E> TRAY FEEDER(CH %d)不在预置状态 |
| $5503 <$E> Error detected in the communication command of the Tray Feeder(CH %d). | $5503 <$E> 错误被检测在TRAY FEEDER(CH %d)数据运行中 |
| $5504 <$E> Error detected in the communication data of the Tray Feeder(CH %d). | $5504 <$E> 错误被检测在TRAY FEEDER(CH %d)数据交换中 |
| $5505 <$E> No palette in the Tray Feeder(CH %d). | $5505 <$E> 无标志在TRAY FEEDER(CH %d)中 |
| $5506 <$E> Time-out error occurred in the Tray Feeder(CH %d). | $5506 <$E> 延时错误发生在TRAY FEEDER(CH %d) |
| $5507 <$E> TRAY_NO_DATA_ERROR(CH %d) occurred. | $5507 <$E> TRAY没有数据错误(CH %d)发生 |
| $5508 <$E> TRAY_INVALID_PR_ERROR(CH %d) occurred. | $5508 <$E> TRAY无效的当前错误(CH %d)发生 |
| $5509 <$E> TRAY_SENDING_ERROR(CH %d) occurred. | $5509 <$E> TRAY传送错误(CH %d)发生 |
| $550a <$E> TRAY_INVALID_RES_ERROR occurred. | $550a <$E> TRAY无效记录错误(CH %D)发生 |
| $550b <$E> TRAY_INVALID_CMD_ERROR(CH %d) occurred. | $550b <$E> TRAY无效CMD错误(CH %d)发生 |
| $550c <$E> Unexpected part exists on the Shuttle Pad. | $550c <$E> Unexpected part exists on the Shuttle Pad. |
| $550d <$E> Upper Magazine of Tray Feeder is not ready. | $550d <$E> 上部分IC盘未准备。 |
| $550e <$E> Lower Magazine of Tray Feeder is not ready. | $550e <$E> 下部分IC盘未准备。 |
| $550f <$E> | $550f <$E> TIME OUT occurred while checking Tray Feeder Status |
| $55ff <$E> TRAY_NOT_DEFINED | $55ff <$E> TRAY盘未定义 |
| $5800 <$E> $F Head $H $P $N Vacuum Check Error occurred. | $5800 <$E> $F 头 $H $P $N 真空检测错误发生 |
| $5801 <$E> $F Head $H $P $N Vision Check Error occurred. | $5801 <$E> $F 头 $H $P $N 视觉检测错误发生 |
| $6001 <$E> MIRROR cannot be opened. | $6001 <$E> 镜子不能够被打开。 |
| $6002 <$E> ANC shutter cannot be opened. | $6002 <$E> ANC气阀不能够打开。 |
| $6003 <$E> ANC shutter cannot be closed. | $6003 <$E> ANC气阀不能够关闭。 |
| $6004 <$E> XY could not move to the Nozzle PUT position. | $6004 <$E> XY 不能移到放喷嘴位置。 |
| $6005 <$E> Z-axis PORT can not be found ( S/W error ). | $6005 <$E> Z轴端口不能找到。 ( 软件错误 ) |
| $6006 <$E> SET_AXIS_ADDON_ERROR. ( S/W error ) | $6006 <$E> SET_AXIS_ADDON_ERROR。 ( S/ W 错误 ) |
| $6007 <$E> Invalid PUT Nozzle data. ( S/W error ) | $6007 <$E> 无效的放吸嘴数据。 ( S/ W 错误 ) |
| $6008 <$E> Selected pocket has a nozzle. [ANC] | $6008 <$E> 选择孔位已有一个吸嘴。 [ANC] |
| $6009 <$E> Selected Pocket does not have nozzle.[ANC] | $6009 <$E> 选择孔位没有一个吸嘴 [ANC]。 |
| $600a <$E> Failed to move to the nozzle pick position. | $600a <$E> 无法移到吸嘴吸取位置。 |
| $600b <$E> Incorrect CHECK SUM of BACKUP SRAM. Initializing ANC and nozzle data. | $600b <$E> 记数检查备份存储器错误导致初始化ANC和吸嘴数据, |
| $600c <$E> Nozzle ID is absent in Part Data. | $600c <$E> 吸嘴数据在元件库中未指定。 |
| $600d <$E> Failed in automatic inquiry for available Nozzle ID. (Put action) | $600d <$E> 自动检查有效吸嘴的验证失败 (放吸嘴动作) |
| $600e <$E> Failed in automatic inquiry for available Nozzle ID. (Put action) | $600e <$E> 自动检查有效吸嘴的验证失败 (放吸嘴动作) |
| $600f <$E> Invalid Nozzle length. | $600f <$E> 无效的嘴长度。 |
| $6010 <$E> Failed to move the Z-axis to the nozzle inspection sensor position. | $6010 <$E> 无法移动Z轴到吸嘴感应器检测位置。 |
| $6020 <$E> Unable to PUT due to absence of nozzle at Head $H. | $6020 <$E> 不能放吸嘴因头$H本身无吸嘴 |
| $6030 <$E> Nozzle is present at Head $H. already. Failed to PUT. | $6030 <$E> 吸嘴已经在$H头,无法放下。 |
| $6040 <$E> Failed to move Z-axis to the PUT position. | $6040 <$E> 无法移到吸嘴放下位置。 |
| $6050 <$E> Failed to move Z-axis to the safety height after the PUT. | $6050 <$E> 放吸嘴后无法移动Z轴到安全高度 |
| $6060 <$E> Unable to GET due to presence of nozzle at Head $H. | $6060 <$E> 无法吸取吸嘴由于吸嘴已在$H头。 |
| $6070 <$E> Nozzle is absent at Head $H. Failed to GET. | $6070 <$E> 孔位无吸嘴导致$H头无法拾取。 |
| $6080 <$E> Failed to move Z-axis to the GET position. | $6080 <$E> 无法移动Z轴到拾取吸嘴位置。 |
| $6090 <$E> Failed to move Z-axis to the safety height after the GET. | $6090 <$E> 拾取吸嘴后无法移动Z轴到安全高度 |
| $60a0 <$E> NOZZLE_EMPTY_ERROR | $60a0 <$E> 吸嘴数据不存在错误 |
| $60b0 <$E> NOZZLE_EXIST_ERROR | $60b0 <$E> 吸嘴数据存在错误 |
| $60b1 <$E> Unable to check the existence of nozzle without light | $60b1 <$E> 没有光不能检查吸嘴的存在 |
| $60c0 <$E> SET_NOZZLE_POINT_ERROR | $60c0 <$E> 设置吸嘴错误 |
| $6501 <$E> MIRROR cannot be opened. | $6501 <$E> 镜子不能打开。 |
| $6502 <$E> ANC shutter cannot be opened. | $6502 <$E> ANC孔位气阀不能够打开。 |
| $6503 <$E> ANC shutter cannot be closed. | $6503 <$E> ANC孔位气阀不能关闭。 |
| $6504 <$E> Failed to move to the Nozzle PUT position. | $6504 <$E> 无法移到放吸嘴的位置 |
| $6505 <$E> Failed to find Z-axis PORT. ( S/W error ) | $6505 <$E> 无法找到Z轴端口.(软件错误 ) |
| $6506 <$E> SET_AXIS_ADDON_ERROR. ( S/W error ) | $6506 <$E> SET_AXIS_ADDON_ERROR。 (软件错误 ) |
| $6507 <$E> Invalid PUT nozzle data. ( S/W error ) | $6507 <$E> 无效的放吸嘴数据.(软件错误 ) |
| $6508 <$E> Both Head $H and ANC have nozzles. | $6508 <$E> $H头和ANC都有吸嘴。 |
| $6509 <$E> ANC does not have nozzle to be used at Head $H. | $6509 <$E> ANC里没有吸嘴来给$H头用。 |
| $650a <$E> Error in ANC nozzle data.( S/W error ) | $650a <$E> 在ANC吸嘴数据错误。(软件错误 ) |
| $650b <$E> Failed to move to the nozzle PICK position. | $650b <$E> 无法移到吸嘴拾取位置。 |
| $650c <$E> Head $H does not have nozzle. | $650c <$E> $H头没有吸嘴。 |
| $650d <$E> Head $H has nozzle. | $650d <$E> $H头有吸嘴。 |
| $6510 <$E> Failed to move the Z-axis to the nozzle inspection sensor position. | $6510 <$E> 无法移动Z轴到吸嘴感应器检测位置。 |
| $6520 <$E> Unable to PUT due to absence of nozzle at Head $H. | $6520 <$E> 不能放吸嘴因头$H本身无吸嘴 |
| $6530 <$E> Nozzle is present at Head $H. Failed to PUT. | $6530 <$E> 吸嘴在$H头无法放下。 |
| $6540 <$E> Failed to move Z-axis to the PUT position. | $6540 <$E> 无法移动Z轴到放吸嘴位置。 |
| $6550 <$E> Failed to move Z-axis to the safety height after the PUT. | $6550 <$E> 放吸嘴后无法移动Z轴到安全高度 |
| $6560 <$E> Unable to GET due to presence of nozzle at Head $H. | $6560 <$E> 不能换取吸嘴由于吸嘴在$H头。 |
| $6570 <$E> Nozzle is absent at Head $H. Failed to GET. | $6570 <$E> 吸嘴在$H头无法更换。 |
| $6580 <$E> Failed to move Z-axis to the GET position. | $6580 <$E> 无法移动Z轴到吸取吸嘴位置 |
| $6590 <$E> Failed to move Z-axis to the safety height after the GET. | $6590 <$E> 吸取吸嘴后无法移动Z轴到安全高度 |
| $6600 <$E> Vac Z-Offset | $6600 <$E> Vac Z-Offset |
| $7000 <$E> Attempted to use unsupported part alignment method. | $7000 <$E> 试图使用元件校正不支持方式。 |
| $a100 <$E> (Vision) Error in processing the fiducial mark. | $a100 <$E> (视觉)处理基准点的错误。 |
| $a110 <$E> (Vision) Abnormality in fiducial mark information. | $a110 <$E> (视觉)无效的基准点数据 |
| $a120 <$E> (Vision) Failed to grab the fiducial mark. | $a120 <$E> (视觉)无法抓取基准点 |
| $a130 <$E> (Vision) Failed to recognize the fiducial mark. | $a130 <$E> (视觉)无法识别基准点。 |
| $a131 <$E> (Vision) Failed to recognize the first PCB fiducial mark. | $a131 <$E> (视觉)无法识别第一块电路板的基准点。 |
| $a132 <$E> (Vision) Failed to recognize the second PCB fiducial mark. | $a132 <$E> (视觉)无法识别第二块电路板的基准点。 |
| $a133 <$E> (Vision) Failed to recognize the third PCB fiducial mark. | $a133 <$E> (视觉)无法识别第三块电路板的基准点 |
| $a134 <$E> (Vision) Failed to recognize the fourth PCB fiducial mark. | $a134 <$E> (视觉)无法识别第四块电路板的基准点。 |
| $a135 <$E> (Vision) Failed to recognize the first part fiducial mark. | $a135 <$E> (视觉)无法识别第一个元器件的基准点。 |
| $a136 <$E> (Vision) Failed to recognize the second part fiducial mark. | $a136 <$E> (视觉)无法识别第二个元器件的基准点。。 |
| $a137 <$E> (Vision) Failed to recognize the third part fiducial mark. | $a137 <$E> (视觉)无法识别第三个元器件的基准点。。 |
| $a138 <$E> (Vision) Failed to recognize the fourth part fiducial mark. | $a138 <$E> (视觉)无法识别第四个元器件的基准点。 |
| $a201 <$E> Attempted to use unsupported camera. | $a201 <$E> 试图使用不支持照相机。 |
| $a210 <$E> Recognition has not finished in the fly camera. | $a210 <$E> 没有在飞行照相机中完成识别元件。 |
| $a211 <$E> Error occurred during the recognition task in the fly camera. | $a211 <$E> 错误发生在飞行照相机识别对中过程。 |
| $a212 <$E> Detected TimeOut Error while waiting for a visioin response. | $a212 <$E> 当等待vision 处理过程,发生超时错误 |
| $a213 <$E> Received an Invalid vision response. | $a213 <$E> 接受了一个无效的视觉回应。 |
| $a220 <$E> Recognition has not finished in the upward camera. | $a220 <$E> FIX照相机识别处理未能完成。 |
| $a221 <$E> Error occurred during the recognition task in the upward camera. | $a221 <$E> 错误发生在FIX照相机识别期间。 |
| $a300 <$E> The previous vision command has not been finished. | $a300 <$E> 早先的视觉指令没有完成。 |
| $a401 <$E> Received an Invalid Camera ID. | $a401 <$E> 收到了一个无效的照相机号。 |
| $a402 <$E> Internal error occurred during the vision process. | $a402 <$E> 内部错误在视觉处理期间发生。 |
| $a403 <$E> Failed to generate fiducial data because of incorrect fiducial type. | $a403 <$E> 因为不正确的基准类型导致无法产生基准数据。 |
| $a404 <$E> Unregistered fiducial. | $a404 <$E> 没注册基准数据。 |
| $a405 <$E> Too big fiducial size. | $a405 <$E> 太大的基准点尺寸。 |
| $a406 <$E> Too small fiducial size. | $a406 <$E> 太小的基准点尺寸。 |
| $a407 <$E> Excessive number of fiducials to register. | $a407 <$E> 过多基准点注册记录。 |
| $a408 <$E> Failed to finish the fiducial recognition within the specified time duration. | $a408 <$E> 无法在指定时间内完成基准点的识别。 |
| $a410 <$E> $F Head$H $P Invalid device ID %d. | $a410 <$E> $F头 $H $P无效的设备验证%d。 |
| $a420 <$E> Can not finish vision inspection within specified time. | $a420 <$E> 在特定时间内不能完成视觉检测。 |
| $a5a0 <$E> $F Head$H $P Error during the MFOV Inspection. | $a5a0 <$E> $F 错误发生在MFOV检测期间 |
| $a5b0 <$E> $F Head$H $P No lead is registered for this MFOV view. | $a5b0 <$E> $F 头 $H $P 没有引脚为MFOV 视野注册。 |
| $a5c0 <$E> $F Head$H $P Error in %d view during the MFOV inspection. | $a5c0 <$E> $F 头 $H $P 错误在%d 在 MFOV 检验期间看。 |
| $a5d0 <$E> $F Head$H $P Cannot find the first lead during the MFOV inspection. | $a5d0 <$E> $F 头 $H $P 在MFOV检验期间不能够找第一个引脚。 |
| $a5d1 <$E> $F Head$H $P Invalid first pin found during the MFOV inspection. | $a5d1 <$E> $F 头 $H $P 无效的PIN在MFOV检测期间发现。 |
| $a5d2 <$E> $F Head$H $P Cannot find the end of the lead during the MFOV inspection. | $a5d2 <$E> $F 头 $H $P 在MFOV检测期间不能够找到最后引脚。 |
| $a5d3 <$E> $F Head$H $P MoveLength is too short. | $a5d3 <$E> $F 头 $H $P 移动长度太短。 |
| $a610 <$E> $F Head$H $P Cannot find the first(left-side) lead of the upper-side lead group. | $a610 <$E> $F 头 $H $P 不能够找到最开始引脚(左边)，其位于上面的引脚组内。 |
| $a611 <$E> $F Head$H $P Cannot find the last(right-side) lead of the upper-side lead group. | $a611 <$E> $F 头 $H $P 不能够找到最后引脚(右边)，其位于上面的引脚组内。 |
| $a612 <$E> $F Head$H $P Cannot find the first(upper-side) lead of the left-side lead group. | $a612 <$E> $F 头 $H $P 不能够找到最开始引脚(上部)，其位于左边的引脚组内 |
| $a613 <$E> $F Head$H $P Cannot find the last(lower-side) lead of the left-side lead group. | $a613 <$E> $F 头 $H $P 不能够找到最后引脚(下部)，其位于左边的引脚组内 |
| $a614 <$E> $F Head$H $P Cannot find the first(left-side) lead of the lower-side lead group. | $a614 <$E> $F 头 $H $P 不能够找到最开始引脚(左边)，其位于下面的引脚组内。 |
| $a615 <$E> $F Head$H $P Cannot find the last(right-side) lead of the lower-side lead group. | $a615 <$E> $F 头 $H $P 不能够找到最后引脚(右边)，其位于下面的引脚组内 |
| $a616 <$E> $F Head$H $P Cannot find the first(uppper-side) lead of the right-side lead group. | $a616 <$E> $F 头 $H $P 不能够找到最开始引脚(上面)，其位于右边的引脚组内 |
| $a617 <$E> $F Head$H $P Cannot find the last(lower-side) lead of the right-side lead group. | $a617 <$E> $F 头 $H $P 不能够找到最后引脚(下面)，其位于右边的引脚组内 |
| $a620 <$E> $F Head$H $P LeadGroup %d : Measured pitch(%d) is longer than the registerd maximum value(%d). | $a620 <$E> $F 头 $H $P 引脚组%d:标准间距(%d)比注册最大值要长。 (%d) |
| $a621 <$E> $F Head$H $P LeadGroup %d : Measured pitch(%d) is shorter than the registerd minimum value(%d). | $a621 <$E> $F 头 $H $P 引脚组%d:标准间距(%d)比注册最小值要短。 (%d) |
| $a631 <$E> $F Head$H $P Failed to pick up a part. | $a631 <$E> $F 头 $H $P 无亮度值在上部引脚组最初引脚（左边）位置 |
| $a632 <$E> $F Head$H $P Failed to pick up a part. | $a632 <$E> $F 头 $H $P 无亮度值在左边引脚组最初引脚（上面）位置 |
| $a633 <$E> $F Head$H $P Failed to pick up a part. | $a633 <$E> $F 头 $H $P 无亮度值在下面引脚组最初引脚（左边）位置 |
| $a634 <$E> $F Head$H $P Failed to pick up a part. | $a634 <$E> $F 头 $H $P 无亮度值在右边引脚组最初引脚（上部）位置 |
| $a635 <$E> $F Head$H $P No edge(%d) pixel on first(left-side) lead position of the upper-side leadGroup. | $a635 <$E> $F 头 $H $P 边像数值在上部引脚组最初引脚（左边）位置 |
| $a636 <$E> $F Head$H $P No edge(%d) pixel on first(upper-side) lead position of the left-side leadGroup. | $a636 <$E> $F 头 $H $P 边像数值在左边引脚组最初引脚（上面）位置 |
| $a637 <$E> $F Head$H $P No edge(%d) pixel on first(left-side) lead position of the lower-side leadGroup. | $a637 <$E> $F 头 $H $P 边像数值在下面引脚组最初引脚（左边）位置 |
| $a638 <$E> $F Head$H $P No edge(%d) pixel on first(upper-side) lead position of the right-side leadGroup. | $a638 <$E> $F 头 $H $P 边像数值在右边引脚组最初引脚（上部）位置 |
| $a641 <$E> $F Head$H $P Erronous bright pixel found on first(left-side) lead position of the upper-side leadGroup. | $a641 <$E> $F 头 $H $P 错误的亮度像素值出现在上部引脚组靠(左边)第一个引脚位置。 |
| $a642 <$E> $F Head$H $P Erronous bright pixel found on first(upper-side) lead position of the left-side leadGroup. | $a642 <$E> $F 头 $H $P 错误的亮度像素值出现在左部引脚组靠(上边)第一个引脚位置 |
| $a643 <$E> $F Head$H $P Erronous bright pixel found on first(left-side) lead position of the lower-side leadGroup. | $a643 <$E> $F 头 $H $P 错误的亮度像素值出现在下部引脚组靠(左边)第一个引脚位置 |
| $a644 <$E> $F Head$H $P Erronous bright pixel found on first(upper-side) lead position of the right-side leadGroup. | $a644 <$E> $F 头 $H $P 错误的亮度像素值出现在右边引脚组靠(上边)第一个引脚位置 |
| $a645 <$E> $F Head$H $P Not enough edge points on first(left-side) lead position of the upper-side leadGroup. | $a645 <$E> $F 头 $H $P 不充足的边缘光出现在上部引脚组靠(左边)第一个引脚位置 |
| $a646 <$E> $F Head$H $P Not enough edge points on first(upper-side) lead position of the left-side leadGroup. | $a646 <$E> $F 头 $ H$P 不充足的边缘光出现在左部引脚组靠(上边)第一个引脚位置。 |
| $a647 <$E> $F Head$H $P Not enough edge points on first(left-side) lead position of the lower-side leadGroup. | $a647 <$E> $F 头 $H $P 不充足的边缘光出现在下部引脚组靠(左边)第一个引脚位置 |
| $a648 <$E> $F Head$H $P Not enough edge points on first(upper-side) lead position of the right-side leadGroup. | $a648 <$E> $F 头 $H $P 不充足的边缘光出现在右部引脚组靠(上边)第一个引脚位置。 |
| $a649 <$E> $F Head$H $P First(left) lead of the upper-side leadGroup is not straight. | $a649 <$E> $F 头 $H $P 上侧引脚组靠左第一个位置引脚不直。 |
| $a64a <$E> $F Head$H $P First(upper) lead of the left-side leadGroup is not straight. | $a64a <$E> $F 头 $H $P 左侧引脚组靠上第一个位置引脚不直。 |
| $a64b <$E> $F Head$H $P First(left) lead of the lower-side leadGroup is not straight. | $a64b <$E> $F 头 $H $P 下侧引脚组靠左第一个位置引脚不直。 |
| $a64c <$E> $F Head$H $P First(upper) lead of the right-side leadGroup is not straight. | $a64c <$E> $F 头 $H $P 右侧引脚组靠上第一个位置引脚不直。 |
| $a651 <$E> $F Head$H $P No bright(%d) pixel on the last(right-side) lead position of the upper-side leadGroup. | $a651 <$E> $F 头 $H $P 无亮度值在上部引脚组靠(右边）最后引脚位置 |
| $a652 <$E> $F Head$H $P No bright(%d) pixel on the last(lower-side) lead position of the left-side leadGroup. | $a652 <$E> $F 头 $H $P 无亮度值在左部引脚组靠(下边）最后引脚位置。 |
| $a653 <$E> $F Head$H $P No bright(%d) pixel on the last(right-side) lead position of the lower-side leadGroup. | $a653 <$E> $F 头 $H $P 无亮度值在下部引脚组靠(右边）最后引脚位置 |
| $a654 <$E> $F Head$H $P No bright(%d) pixel on the last(lower-side) lead position of the right-side leadGroup. | $a654 <$E> $F 头 $H $P 无亮度值在右部引脚组靠(上边）最后引脚位置。 |
| $a660 <$E> $F Head$H $P Dir%d LeadGroup%d : Cannot find any lead. | $a660 <$E> $F 头 $H $P Dir%d LeadGroup%d: 不能发现任何引脚。 |
| $a665 <$E> $F Head$H $P Dir%d LeadGroup%d : Number of leads not matched (Found %d, Registerd %d). | $a665 <$E> $F 头 $H $P Dir%d LeadGroup%d: 引脚数不匹配。 ( 发现%d,注册%d) |
| $a671 <$E> $F Head$H $P Dir%d LeadGroup%d : Number of leads not matched (Found %d, Registerd %d). | $a671 <$E> $F 头 $H $P Dir%d LeadGroup%d: 引脚数不匹配。 ( 发现%d,注册%d) |
| $a672 <$E> $F Head$H $P Dir%d LeadGroup%d : Number of leads not matched (Found %d, Registerd %d). | $a672 <$E> $F 头 $H $P Dir%d LeadGroup%d: 引脚数不匹配。 ( 发现%d,注册%d) |
| $a673 <$E> $F Head$H $P Dir%d LeadGroup%d : Number of leads not matched (Found %d, Registerd %d). | $a673 <$E> $F 头 $H $P Dir%d LeadGroup%d: 引脚数不匹配。 ( 发现%d,注册%d) |
| $a674 <$E> $F Head$H $P Dir%d LeadGroup%d : Number of leads not matched (Found %d, Registerd %d). | $a674 <$E> $F 头 $H $P Dir%d LeadGroup%d: 引脚数不匹配。 ( 发现%d,注册%d) |
| $a680 <$E> $F Head$H $P Dir%d LeadGroup%d : Number of leads not matched (Found %d, Registerd %d). | $a680 <$E> $F 头 $H $P Dir%d LeadGroup%d: 引脚数不匹配。 ( 发现%d,注册%d) |
| $a711 <$E> Cannot find the first(left) lead of the upper-side leadgroup. | $a711 <$E> 不能找到上部引脚组(左边)第一个引脚。 |
| $a712 <$E> Cannot find the first(up) lead of the left-side leadgroup. | $a712 <$E> 不能找到左部引脚组(上边)第一个引脚。。 |
| $a713 <$E> Cannot find the first(left) lead of the lower-side leadgroup. | $a713 <$E> 不能找到右部引脚组(左部)第一个引脚。。 |
| $a714 <$E> Cannot find the first(up) lead of the right-side leadgroup. | $a714 <$E> 不能找到右部引脚组(上边)第一个引脚。 |
| $a715 <$E> Cannot find the last(right) lead of the upper-side leadgroup. | $a715 <$E> 不能找到上部引脚组(右边)最后一个引脚。 |
| $a716 <$E> Cannot find the last(down) lead of the left-side leadgroup. | $a716 <$E> 不能找到左部引脚组(下边)最后一个引脚。 |
| $a717 <$E> Cannot find the last(right) lead of the lower-side leadgroup. | $a717 <$E> 不能找到下部引脚组(右边)最后一个引脚。 |
| $a718 <$E> Cannot find the last(down) lead of the right-side leadgroup. | $a718 <$E> 不能找到右部引脚组(下边)最后一个引脚。 |
| $a721 <$E> The length of the uppper-side leadgroup does not match the one found. | $a721 <$E> 上部引脚组长度不匹配。 |
| $a722 <$E> The length of the left-side leadgroup does not match the one found. | $a722 <$E> 左部引脚组长度不匹配。 |
| $a723 <$E> The length of the lower-side leadgroup does not match the one found. | $a723 <$E> 下部引脚组长度不匹配 |
| $a724 <$E> The length of the right-side leadgroup does not match the one found. | $a724 <$E> 右部引脚组长度不匹配 |
| $a731 <$E> Cannot find the accurate position of the upper-side leads. | $a731 <$E> 不能找到上部引脚的正确位置。 |
| $a732 <$E> Cannot find the accurate position of the left-side leads. | $a732 <$E> 不能找到左部引脚的正确位置。 |
| $a733 <$E> Cannot find the accurate position of the lower-side leads. | $a733 <$E> 不能找到下部引脚的正确位置。 |
| $a734 <$E> Cannot find the accurate position of the right-side leads. | $a734 <$E> 不能找到右部引脚的正确位置。 |
| $a741 <$E> Excessively bright area exists near upward leadgroup. | $a741 <$E> 在靠近朝上的引脚组边有过度的明亮区域。 |
| $a742 <$E> Excessively bright area exists near left leadgroup. | $a742 <$E> 在靠左的引脚组边有过度的明亮区域。。 |
| $a743 <$E> Excessively bright area exists near downward leadgroup. | $a743 <$E> 在靠下的引脚组边有过度的明亮区域。。 |
| $a744 <$E> Excessively bright area exists near right leadgroup. | $a744 <$E> 在靠右的引脚组边有过度的明亮区域。。 |
| $a751 <$E> Cannot find the upper-side leadgroup. | $a751 <$E> 不能够找到朝上的引脚组。 |
| $a752 <$E> Cannot find the left-side leadgroup. | $a752 <$E> 不能够找到朝左的引脚组。 |
| $a753 <$E> Cannot find the lower-side leadgroup. | $a753 <$E> 不能够找到朝下的引脚组。 |
| $a754 <$E> Cannot find the right-side leadgroup. | $a754 <$E> 不能够找到朝右的引脚组。 |
| $a761 <$E> Not enough information to find the upper-side leadgroup. | $a761 <$E> 上面引脚组数据不充足。 |
| $a762 <$E> Not enough information to find the left-side leadgroup. | $a762 <$E> 左面引脚组数据不充足 |
| $a763 <$E> Not enough information to find the lower-side leadgroup. | $a763 <$E> 下面引脚组数据不充足 |
| $a764 <$E> Not enough information to find the right-side leadgroup. | $a764 <$E> 右面引脚组数据不充足 |
| $a805 <$E> $F Head$H $P Failed to execute the recognition during the part recognition task. | $a805 <$E> $F 头 $H $P 在元件识别任务期间识别失败。 |
| $a810 <$E> $F Head$H $P Error in calculation relating to the part recognition task. | $a810 <$E> $F 头 $H $P 在元件识别任务期间相关的计算错误。 |
| $a811 <$E> $F Head$H $P Failed to calculate the part angle during the part recognition task. | $a811 <$E> $F 头 $H $P 在元件识别任务期间计算元件角度失败。 |
| $a812 <$E> $F Head$H $P Failed to calculate the intersection point during the part recognition task. | $a812 <$E> $F 头 $H $P 在元件识别任务期间计算元件交叉点数失败。 |
| $a820 <$E> $F Head$H $P Error occurred during the part recognition task. | $a820 <$E> $F 头 $H $P 错误发生在元件识别任务期间。 |
| $a821 <$E> $F Head$H $P Part's surface area is not consistent with the registered value. | $a821 <$E> $F 头 $H $P 元件的表面区域与注册值不一致。 |
| $a822 <$E> $F Head$H $P Width of a part (in X) is not consistent with the registered value. | $a822 <$E> $F 头 $H $P 元件宽度X方向与注册值不一致。 |
| $a823 <$E> $F Head$H $P Width of a part (in Y) is not consistent with the registered value. | $a823 <$E> $F 头 $H $P 元件宽度Y方向与注册值不一致。 |
| $a824 <$E> $F Head$H $P Center position of a part is too eccentric in the X direction. | $a824 <$E> $F 头 $H $P X方向元件中心位置太怪。 |
| $a825 <$E> $F Head$H $P Center position of a part is too eccentric in the Y direction. | $a825 <$E> $F 头 $H $P Y方向元件中心位置太怪。 |
| $a826 <$E> $F Head$H $P Angle of a part is too large. | $a826 <$E> $F 头 $H $P 元件角度太大。 |
| $a830 <$E> $F Head$H $P No object is seen in the search area. | $a830 <$E> $F 头 $H $P 搜寻区域不能找到目标。 |
| $a831 <$E> $F Head$H $P Background of the image is too bright. | $a831 <$E> $F 头 $H $P 背景太亮。 |
| $a832 <$E> $F Head$H $P Part is seen too darkly. | $a832 <$E> $F 头 $H $P 元件太暗。 |
| $a833 <$E> $F Head$H $P Failed to find out the boundaries of a component. | $a833 <$E> $F 头 $H $P 无法找到元件边界。 |
| $a840 <$E> $F Head$H $P Error relating to the pin recognition occurred. | $a840 <$E> $F 头 $H $P 错误与脚识别有关。 |
| $a841 <$E> $F Head$H $P Too short the length of the longest side. | $a841 <$E> $F 头 $H $P 最长的边长度太短。 |
| $a842 <$E> $F Head$H $P Failed to search the first pin between both ends of a lead group | $a842 <$E> $F 头 $H $P 无法找到引脚组开始到结束之间的第一脚 |
| $a843 <$E> $F Head$H $P Failed to search the last pin between both ends of a lead group | $a843 <$E> $F 头 $H $P 无法找到每排脚的最后一个脚 |
| $a844 <$E> $F Head$H $P Recognized pin numbers of a lead group are very few. (less than 4) | $a844 <$E> $F 头 $H $P每排脚中能被识别出的脚的数量很少（少于四个） |
| $a845 <$E> $F Head$H $P Pin is absent that has to be in a lead group. | $a845 <$E> $F 头 $H $P在一排脚中有缺脚 |
| $a846 <$E> $F Head$H $P Pitch of a lead group is beyond the admissible value. | $a846 <$E> $F 头 $H $P一排脚中的脚距超过可接受范围 |
| $a847 <$E> $F Head$H $P Failed to find out the boundaries required to seek pins in a lead group. | $a847 <$E> $F 头 $H $P不能识别出一排脚中脚的轮廓 |
| $a848 <$E> $F Head$H $P Width and foot are too large among the recognized lead parameters. | $a848 <$E> $F 头 $H $P 脚的宽度和脚的末端尺寸超过范围 |
| $a850 <$E> $F Head$H $P Failed in Crack-coding. | $a850 <$E> $F 头 $H $P代码识别错误 |
| $a851 <$E> $F Head$H $P Too many objects have been filtered out. | $a851 <$E> $F 头 $H $P 太多目标被过滤出。 |
| $a852 <$E> $F Head$H $P Code length exceeded the maximum value. | $a852 <$E> $F 头 $H $P 密码长度超过了最大值。 |
| $a860 <$E> $F Head$H $P Error occurred during the execution of MinWIdth algorithm. | $a860 <$E> $F 头 $H $P 在 MinWIdth 数值计算的执行期间发生错误。 |
| $a861 <$E> $F Head$H $P Backlight is not supported in MinWidth algorithm. | $a861 <$E> $F 头 $H $P 在 MinWidth数值计算中不支持Backlight 。 |
| $a910 <$E> $F Head$H $P (Vision) Direction Mark is out of inspection range. | $a910 <$E> $F 头 $H$MARK尺寸超过检查范围 |
| $a911 <$E> $F Head$H $P (Vision) Direction Mark is too dark. | $a911 <$E> $F 头 $H$(视觉) MARK太黑。 |
| $a912 <$E> $F Head$H $P (Vision) Direction Mark is too bright. | $a912 <$E> $F 头 $H$(视觉) MARK太亮。 |
| $a913 <$E> $F Head$H $P (Vision) Abnormal BGA information. | $a913 <$E> $F 领导 $H $P(视觉) BGA 数据不正常。 |
| $a914 <$E> $F Head$H $P (Vision) Ball size is too Small. | $a914 <$E> $F 头 $H $P(视觉) 球大小太小。 |
| $a915 <$E> $F Head$H $P (Vision) Ball size is too large. | $a915 <$E> $F 头 $H $P(视觉) 球大小是太大的。 |
| $a916 <$E> $F Head$H $P (Vision) Can't find search direction. | $a916 <$E> $F 头 $H $P(视觉) 不能发现搜寻方向。 |
| $a917 <$E> $F Head$H $P (Vision) Abnormal search direction. | $a917 <$E> $F 头 $H $P(视觉) 搜寻方向不正确。 |
| $a918 <$E> $F Head$H $P (Vision) Failed to recognize the reference row of balls. | $a918 <$E> $F 头 $H $P(视觉) 识别球的排数有错。 |
| $a919 <$E> $F Head$H $P (Vision) Can't find the rough center. | $a919 <$E> $F 头 $H $P(视觉) 不能识别元件中心。 |
| $a91a <$E> $F Head$H $P (Vision) Failed to recognize the reference balls. | $a91a <$E> $F 头 $H $P(视觉) 无法识别球。 |
| $a91b <$E> $F Head$H $P (Vision) Failed to recognize the balls finely . | $a91b <$E> $F 头 $H $P(视觉) 无法精确地识别球。 |
| $a920 <$E> $F Head$H $P (Vision) can't find the body . | $a920 <$E> $F 头 $H $P(视觉) 不能识别本体 |
| $aa00 <$E> $F Head$H $P Incorrect angle value has been transmitted from VME. | $aa00 <$E> $F 头 $H $P从 VME传出不正确的角度值。 |
| $aa01 <$E> $F Head$H $P Too low threshold value. | $aa01 <$E> $F 头 $H $P 太低阀值 |
| $aa02 <$E> $F Head$H $P Too high threshold value. | $aa02 <$E> $F 头 $H $P 太高的阀值。 |
| $aa03 <$E> $F Head$H $P Not Used | $aa03 <$E> $F 头 $H $P 不用 |
| $aa04 <$E> $F Head$H $P Failed to find out parts. | $aa04 <$E> $F 头 $H $P 无法识别元件 |
| $aa05 <$E> $F Head$H $P Incorrect algorithm. | $aa05 <$E> $F 领导 $H $P 不正确的数值计算 |
| $aa06 <$E> $F Head$H $P Error occurred during execution of internal function. | $aa06 <$E> $F 头 $H $P 错误在内部功能执行期间发生。 |
| $aa07 <$E> $F Head$H $P Part's size is different from registered value. | $aa07 <$E> $F 头 $H $P元件尺寸不同於设定值 |
| $aa08 <$E> $F Head$H $P Part's size is different from registered value. | $aa08 <$E> $F 头 $H $P元件大小不同於设定值 |
| $aa09 <$E> $F Head$H $P Part's center position is too eccentric. | $aa09 <$E> $F 头 $H $P 部份的中心位置偏差太大 |
| $aa0a <$E> $F Head$H $P Part's center position is too eccentric. | $aa0a <$E> $F 头 $H $P 部份的中心位置偏差太大 |
| $aa0b <$E> $F Head$H $P Part's angle is beyond the reference value. | $aa0b <$E> $F 头 $H $P元件的角度超过设定值。 |
| $aa0c <$E> $F Head$H $P Internal function Error (MelfFindOut). | $aa0c <$E> $F 领导 $H $P 内在的功能错误。 (MelfFindOut) |
| $aa0d <$E> $F Head$H $P Internal function Error (MelfAreaSort) | $aa0d <$E> $F 头 $H $P 内在的功能错误 (MelfAreaSort) |
| $aa0e <$E> $F Head$H $P Part's size is too small. | $aa0e <$E> $F 头 $H $P 元件尺寸太小。 |
| $aa0f <$E> $F Head$H $P Height of part's lead is recognized lower than its real one. | $aa0f <$E> $F识别元件脚的宽度低于设定值 |
| $aa10 <$E> $F Head$H $P Height of part's lead is recognized higher than its real one. | $aa10 <$E> $F识别元件脚的宽度高于设定值 |
| $aa11 <$E> $F Head$H $P Part's surface area is too small. | $aa11 <$E> $F 头 $H $P 部份的表面区域太小。 |
| $aa12 <$E> $F Head$H $P Part's surface area is too large. | $aa12 <$E> $F 头 $H $P 部份的表面区域是太大。 |
| $aa13 <$E> $F Head$H $P Not Used | $aa13 <$E> $F 头 $H $P 不用 |
| $aa14 <$E> $F Head$H $P Part's center position is too eccentric. | $aa14 <$E> $F 头 $H $P 部份的中心位置偏差太大 |
| $aa15 <$E> $F Head$H $P Error occurred during the calculation of the edge data. | $aa15 <$E> $F 头 $H $P 错误在轮阔数据的计算期间发生。 |
| $aa16 <$E> $F Head$H $P Error occurred during the calculation of the part's angle. | $aa16 <$E> $F 头 $H $P 错误在元件的角度计算期间发生。 |
| $aa17 <$E> $F Head$H $P Internal function Error(LineFitting) | $aa17 <$E> $F 头 $H $P 内在的功能错误 (LineFitting) |
| $aa18 <$E> $F Head$H $P Internal function Error(LineFitting) | $aa18 <$E> $F 头 $H $P 内在的功能错误 (LineFitting) |
| $aa19 <$E> $F Head$H $P Part's length is recognized larger than its real one. | $aa19 <$E> $F 头 $H $P 识别的元件尺寸大于所设定范围。 |
| $aa1a <$E> $F Head$H $P Part's length is recognized smaller than its real one. | $aa1a <$E> $F 头 $H $P 识别的元件尺寸小于所设定范围。 |
| $aa1b <$E> $F Head$H $P Part's center position is too eccentric. | $aa1b <$E> $F 头 $H $P 部份的中心位置偏差太大 |
| $aa1c <$E> $F Head$H $P Part's center position is too eccentric. | $aa1c <$E> $F 头 $H $P 部份的中心位置偏差太大 |
| $aa1d <$E> $F Head$H $P Part's width is longer than the reference. | $aa1d <$E> $F 头 $H $P 元件的宽度大于所设定范围。 |
| $aa1e <$E> $F Head$H $P Part's width is shorter than the reference. | $aa1e <$E> $F 头 $H $P 元件的宽度小于所设定范围。 |
| $aa1f <$E> $F Head$H $P Failed to pick up a part. | $aa1f <$E> $F 头 $H $P 无法拾起元件 |
| $aa20 <$E> $F Head$H $P Error occurred during the edge detection. | $aa20 <$E> $F 头 $H $P 错误在轮廓检测时发生。 |
| $aa21 <$E> $F Head$H $P Troublesome Threshold value. Raise the value manually. | $aa21 <$E> $F 头 $H $P 不合适的阀域值，手动设定 |
| $aa22 <$E> $F Head$H $P Troublesome Threshold value. Raise the value manually. | $aa22 <$E> $F 头 $H $P 不合适的阀域值，手动设定 |
| $ab00 <$E> $F Head$H $P Incorrect angle value has been transmitted from VME. | $ab00 <$E> $F 头 $H $P 从 VME输出的角度值不正确。 |
| $ab01 <$E> $F Head$H $P Incorrect algorithm number has been transmitted from VME. | $ab01 <$E> $F 头 $H $P 从 VME输出的数值不正确。 |
| $ab02 <$E> $F Head$H $P Number of lower pins should be more than 2 in case of checking Heat. | $ab02 <$E> $F 检测脚的浮翘时，较底的脚的数量至少两个 |
| $ab03 <$E> $F Head$H $P Too low threshold value. | $ab03 <$E> $F 头 $H $P 太低的门限值。 |
| $ab04 <$E> $F Head$H $P Too high threshold value.H288 | $ab04 <$E> $F 头 $H $P 太高的门限值 |
| $ab05 <$E> $F Head$H $P Not used | $ab05 <$E> $F 头 $H $P 不用 |
| $ab06 <$E> $F Head$H $P Not used | $ab06 <$E> $F 头 $H $P 不用 |
| $ab07 <$E> $F Head$H $P Unable to find out the lead. | $ab07 <$E> $F 不能识别脚 |
| $ab08 <$E> $F Head$H $P Internal function Error(FindLeadInformation). | $ab08 <$E> $F 领导 $H $P 内在的功能错误。 (FindLeadInformation) |
| $ab09 <$E> $F Head$H $P Lead size is too big. | $ab09 <$E> $F 头 $H $P 脚的尺寸太大 |
| $ab0a <$E> $F Head$H $P Projection area is beyond the inspection area. | $ab0a <$E> $F 头 $H $P 所识别的目标不在检测区域 |
| $ab0b <$E> $F Head$H $P Lead width is beyond the reference length. | $ab0b <$E> $F 头 $H $P 脚宽度超过设定范围。 |
| $ab0c <$E> $F Head$H $P Error occurred during the lead inspection. | $ab0c <$E> $F 头 $H $P 脚的检测发生错误 |
| $ab0d <$E> $F Head$H $P Incorrect lead numbers. | $ab0d <$E> $F 头 $H $P 错误的脚数 |
| $ab0e <$E> $F Head$H $P Error occurred during the search for lead for angle calculation's sake. | $ab0e <$E> $F 头 $H $P 脚的角度识别发生错误 |
| $ab0f <$E> $F Head$H $P Incorrect angle calculated from the lead. | $ab0f <$E> $F 头 $H $P 脚的角度计算发生错误 |
| $ab10 <$E> $F Head$H $P Angle calculated from the lead is beyond the reference one. | $ab10 <$E> $F 头 $H $P 识别的脚的角度超过设定值 |
| $ab11 <$E> $F Head$H $P Internal function Error(M Lead line). | $ab11 <$E> $F 领导 $H $P 内在的功能错误。 (M ) |
| $ab12 <$E> $F Head$H $P Internal function Error(M Lead line). | $ab12 <$E> $F 领导 $H $P 内在的功能错误。 (M ) |
| $ab13 <$E> $F Head$H $P Part's height is beyond the reference one. | $ab13 <$E> $F 头 $H $P 元件的宽度超过所设定范围。 |
| $ab14 <$E> $F Head$H $P Divided by 0 in calculating angle. | $ab14 <$E> $F 计算的角度被0分开 |
| $ab15 <$E> $F Head$H $P Upper lead's pitch is beyond the reference value. | $ab15 <$E> $F 头 $H $P上边的脚距超过可接受范围 |
| $ab16 <$E> $F Head$H $P Lower lead's pitch is beyond the reference value. | $ab16 <$E> $F 头 $H $P下边的脚距超过可接受范围 |
| $ab17 <$E> $F Head$H $P Each distance between the upper leads is beyond the reference value. | $ab17 <$E> $F 头 $H $P上边每个脚距超过可接受范围 |
| $ab18 <$E> $F Head$H $P Each distance between the lower leads is beyond the reference value. | $ab18 <$E> $F 头 $H $P下边的每个脚距超过可接受范围 |
| $ab19 <$E> $F Head$H $P Part's angle is beyond the reference value. | $ab19 <$E> $F 头 $H $P 元件的脚度超过设定值 |
| $ab1a <$E> $F Head$H $P Each angle between the upper leads is beyond the reference value. | $ab1a <$E> $F 头 $H $P上边每个脚角度超过可接受范围 |
| $ab1b <$E> $F Head$H $P Each angle between the lower leads is beyond the reference value. | $ab1b <$E> $F 头 $H $P下边每个脚角度超过可接受范围 |
| $ab1c <$E> $F Head$H $P Too many number of leads in the screen. | $ab1c <$E> $F 领导 $H $P屏幕上显示的脚的数量太多 |
| $ab1d <$E> $F Head$H $P Incorrect algorithm number has been inputted in internal function. | $ab1d <$E> $F 头 $H $P 内部函数被输入了不正确的数值 |
| $ab1e <$E> $F Head$H $P Error occurred during execution of internal function. | $ab1e <$E> $F 头 $H $P 内部函数运算发生错误 |
| $ab1f <$E> $F Head$H $P Internal function Error(TrCenterCorrection). | $ab1f <$E> $F 领导 $H $P 内在的功能错误。 (TrCenterCorrection) |
| $ab20 <$E> $F Head$H $P Internal function Error(TrCenterCorrection). | $ab20 <$E> $F 领导 $H $P 内在的功能错误。 (TrCenterCorrection) |
| $ab21 <$E> $F Head$H $P Total number of leads is less than 2. | $ab21 <$E> $F 头 $H $P 脚的总数是少於 2 。 |
| $ab22 <$E> $F Head$H $P Too many number of leads. | $ab22 <$E> $F 领导 $H $P 太多的脚数 |
| $ab23 <$E> $F Head$H $P Total number of leads is less than 0. | $ab23 <$E> $F 头 $H $P 脚的总数是少於 0 。 |
| $ab24 <$E> $F Head$H $P Algorithm that cannot be defined. | $ab24 <$E> $F 无法定义确定的函数运算 |
| $ab25 <$E> $F Head$H $P Angle the cannot be defined. | $ab25 <$E> $F 无法定义确定的角度 |
| $ab26 <$E> $F Head$H $P Error occurred during the lead inspection. | $ab26 <$E> $F 头 $H $P 脚的检测发生错误 |
| $ab27 <$E> $F Head$H $P Error occurred during the lead inspection. | $ab27 <$E> $F 头 $H $P 脚的检测发生错误 |
| $ab28 <$E> $F Head$H $P Error occurred during the lead inspection. | $ab28 <$E> $F 头 $H $P 脚的检测发生错误 |
| $ab29 <$E> $F Head$H $P Error occurred during the lead inspection. | $ab29 <$E> $F 头 $H $P 脚的检测发生错误 |
| $ab2a <$E> $F Head$H $P Incorrect angle calculated from the lead. | $ab2a <$E> $F 头 $H $P 脚的角度计算发生错误 |
| $ab2b <$E> $F Head$H $P Part's angle is beyond the reference value. | $ab2b <$E> $F 头 $H $P 元件的脚度超过设定值 |
| $ac00 <$E> $F Head$H $P Incorrect angle value has been transmitted from VME. | $ac00 <$E> $F 头 $H $P 从 VME 输出的角度值不正确 |
| $ac01 <$E> $F Head$H $P Error occurred during the data setting. | $ac01 <$E> $F 头 $H $P 错误在数据设定期间发生。 |
| $ac02 <$E> $F Head$H $P Incorrect parameter input. | $ac02 <$E> $F 领导 $H $P 输入的参数不正确 |
| $ac03 <$E> $F Head$H $P Too low threshold value. | $ac03 <$E> $F 头 $H $P 太低的门槛评值。 |
| $ac04 <$E> $F Head$H $P Too high threshold value. | $ac04 <$E> $F 头 $H $P 太高的门槛评值。 |
| $ac05 <$E> $F Head$H $P Not Used | $ac05 <$E> $F 头 $H $P 不用 |
| $ac06 <$E> $F Head$H $P Error occurred during execution of internal function. | $ac06 <$E> $F 头 $H $P 内部功能执行期间发生错误。 |
| $ac07 <$E> $F Head$H $P Part's width is recognized different from the reference value. | $ac07 <$E> $F 头 $H $P 识别元件的宽度与设定值不同 |
| $ac08 <$E> $F Head$H $P Part's height is recognized different from the reference value. | $ac08 <$E> $F 头 $H $P 识别元件的高度与设定值不同 |
| $ac09 <$E> $F Head$H $P Internal function error(CenterCorrection) | $ac09 <$E> $F 头 $H $P 内在的功能错误 (CenterCorrection) |
| $ac0a <$E> $F Head$H $P Algorithm that cannot be defined. | $ac0a <$E> $F 无法定义确定的函数运算 |
| $ac0b <$E> $F Head$H $P Internal function error(LineFitting 1) | $ac0b <$E> $F 头 $H $P 内在的功能错误 (LineFitting 1) |
| $ac0c <$E> $F Head$H $P Internal function error(LineFitting 2) | $ac0c <$E> $F 头 $H $P 内在的功能错误 (LineFitting 2) |
| $ac0d <$E> $F Head$H $P Internal function error(LineFitting 3) | $ac0d <$E> $F 头 $H $P 内在的功能错误 (LineFitting 3) |
| $ac0e <$E> $F Head$H $P Internal function error(LineFitting 4) | $ac0e <$E> $F 头 $H $P 内在的功能错误 (LineFitting 4) |
| $ac0f <$E> $F Head$H $P Internal function error(LineFitting 5) | $ac0f <$E> $F 头 $H $P 内在的功能错误 (LineFitting 5) |
| $ac10 <$E> $F Head$H $P Lead size is too big to recognize. | $ac10 <$E> $F 头 $H $P 脚的尺寸太大，不能检测 |
| $ac11 <$E> $F Head$H $P Part's size is too small or lead's length is set to large. | $ac11 <$E> $F 头 $H $P 脚的尺寸太小，而脚的长度设定值太大 |
| $ac12 <$E> $F Head$H $P Part's width is recognized shorter than the reference one. | $ac12 <$E> $F 头 $H $P元件识别的宽度比设定值小 |
| $ac13 <$E> $F Head$H $P Part's width is recognized longer than the reference one. | $ac13 <$E> $F 头 $H $P元件识别的宽度比设定值大 |
| $ac14 <$E> $F Head$H $P Part's angle is beyond the reference value. | $ac14 <$E> $F 头 $H $P 元件的脚度超过设定值 |
| $ad01 <$E> Invalid part type for AutoTeach. | $ad01 <$E> 自动识别的元件类型不对 |
| $ad02 <$E> Tangential distance must be 0. | $ad02 <$E> 相切的距离一定是 0 。 |
| $ad03 <$E> Number of leads should be more than 4 per side. | $ad03 <$E> 每一边的脚数应该超过 4 。 |
| $ad04 <$E> Gap should not be present in executing AutoTeach. | $ad04 <$E> 缺脚的元件类型不能自动识别 |
| $ad05 <$E> Number of lead groups should be more than 1 per side while executing AutoTeach. | $ad05 <$E> 每一边的脚数应该超过 1的元件才能进行自动识别。 |
| $ad06 <$E> Number of lead parameters is different from that of lead groups and is not equal to 1. | $ad06 <$E> 脚的参数与每一排脚定义有差别，而且不等于1 |
| $ad07 <$E> LeadGroup%d : Failed to find the foot end while executing AutoTeach. | $ad07 <$E> LeadGroup%d: 当运行 AutoTeach 的时候 , 无法找到脚的末端 |
| $ad08 <$E> LeadGroup%d : Failed to find the foot start while executing AutoTeach. | $ad08 <$E> LeadGroup%d: 当运行 AutoTeach 的时候 , 无法寻找脚的起点 |
| $ad09 <$E> LeadGroup%d : Failed to find the border line between foot and lead while executing AutoTeach. | $ad09 <$E> LeadGroup%d: 在AutoTeach的时候，无法识别脚的末端 |
| $ad10 <$E> LeadGroup%d : Failed to find the lead start while executing AutoTeach. | $ad10 <$E> LeadGroup%d: 在AutoTeach的时候，无法识别脚的起点 |
| $ad11 <$E> LeadGroup%d : Number of the rise edges(%d) is different from that of the fall edges(%d). | $ad11 <$E> LeadGroup%d: 上升斜度(%d)和 下降斜度不一样。 (%d) |
| $ad12 <$E> Part's height (or length) is 1 pixel. | $ad12 <$E> 元件的高度 ( 或长度) 是 1个图素。 |
| $ad13 <$E> No sufficiently bright pixels in the display while executing AutoTeach. (Threshold = %d) | $ad13 <$E> 在 AutoTeach的时候，元件象素不够 ( 门槛 =%d) |
| $ad14 <$E> Component went beyond the valid extent while executing AutoTeach. | $ad14 <$E> 当运行 AutoTeach 的时候 , 元件尺寸的偏差超过有效的范围。 |
| $ad15 <$E> LeadGroup%d : Less than 4 leads recognized (%d) while executing AutoTeach. | $ad15 <$E> LeadGroup%d: 当运行 AutoTeach 的时候 , 至少4个脚能识别出 (%d) 。 |
| $ad16 <$E> Excessive(more than +- 20) part angle (%d) . | $ad16 <$E> 超过元件角度+，-20。 (%d) |
| $ad17 <$E> LeadGroup %d, %d : Different numbers(%d, %d) between two lead groups facing each other. | $ad17 <$E> LeadGroup%d,%d:两排相对脚的参数不一样 |
| $ad18 <$E> LeadGroup %d, %d : Large difference in radial distances(%d, %d) between two lead groups facing each other. | $ad18 <$E> LeadGroup%d,%d:两排相对脚的垂直方向的距离大不一样 |
| $ad19 <$E> Large differences in the recognized parameter values while executing the AutoTeach. | $ad19 <$E> 当运行 AutoTeach 的时候 , 识别出的脚的参数也大不一样。 |
| $ad20 <$E> LeadGroup%d : Recognized foot length(%d) is shorter than the lead length(%d). | $ad20 <$E> LeadGroup%d: 识别出来的脚末端长度 (%d) 比脚的长度短。 (%d) |
| $ad21 <$E> LeadGroup%d : Recognized pitch(%d) is narrower than the lead width(%d). | $ad21 <$E> LeadGroup%d: 识别出来的脚距比脚的宽度小 |
| $ad22 <$E> Recognized part size(%d) has negative value. | $ad22 <$E> LeadGroup%d: 识别出来的元件尺寸是负值 |
| $ad30 <$E> LeadGroup %d, %d : Large differences in the recognized lead-width values(%d, %d). | $ad30 <$E> LeadGroup%d: 识别出来的脚宽度差别很大 |
| $ad31 <$E> LeadGroup %d, %d : Large differences in the recognized lead-length values(%d, %d). | $ad31 <$E> LeadGroup%d: 识别出来的脚长度差别很大 |
| $ad32 <$E> LeadGroup %d, %d : Large differences in the recognized lead-pitch values(%d, %d). | $ad32 <$E> LeadGroup%d: 识别出来的脚距差别很大 |
| $ad33 <$E> LeadGroup %d, %d : Large differences in the recognized foot-length values(%d, %d). | $ad33 <$E> LeadGroup%d: 识别出来的脚的末端差别很大 |
| $ae03 <$E> Failed to recognize the fiducial marks. | $ae03 <$E> MARK 识别失败 |
| $b100 <$E> Invalid parameters exist in the manual command. | $b100 <$E> 在手动指令中包含无效参数。 |
| $b202 <$E> Unable to refer to the Head information. | $b202 <$E> 不能参照有关头的数据。 |
| $b203 <$E> Unable to refer to the Tray Feeder information. | $b203 <$E> 不能参照有关盘式喂料器的数据。 |
| $b204 <$E> Unable to refer to the Mount information. | $b204 <$E> 不能参照有关贴装的数据。 |
| $b206 <$E> Invalid R velocity setting exists at part $P. | $b206 <$E> 在元件库中设置了无效的旋转速度 |
| $b207 <$E> No parts found in $F. | $b207 <$E> 没有元件 |
| $b210 <$E> Failed in calculation of the placement angle. | $b210 <$E> 计算贴装角度出错 |
| $b220 <$E> Part $P does NOT have a feeding angle of 90 degree. | $b220 <$E> 没有供料角度为90度的元器件 |
| $b500 <$E> FEEDER_COMMON_ERROR | $b500 <$E> 供料器指令错 |
| $b510 <$E> TAPE_FEEDER_SW_DATA_ERROR | $b510 <$E> 与纸料带相关指令错 |
| $b520 <$E> STOCK_FEEDER_SW_DATA_ERROR | $b520 <$E> 与胶料带相关指令错 |
| $b530 <$E> TRAY_FEEDER_SW_DATA_ERROR | $b530 <$E> 与盘式喂料器相关指令错 |
| $b600 <$E> Invalid PCB Data exist. | $b600 <$E> 无效的PCB数据 |
| $bbbb <$E> Assert Fault occurred. | $bbbb <$E> 错误发生。 |
| $bbbc <$E> Inspection result does not match with the Execution Cycle. | $bbbc <$E> 检验结果用执行周期不相配。 |
| $bbbe <$E> Unable to generate the fiducial data. | $bbbe <$E> 不能产生基准的数据。 |
| $bbbf <$E> Failed to delete the Fiducial Mark Data. | $bbbf <$E> 无法删出基准数据。 |
| $bc00 <$E> Equipment is not in the Ready state. | $bc00 <$E> 设备没有准备好。 |
| $bc01 <$E> PCB Data have not been downloaded yet. | $bc01 <$E> 电路板数据没有装载。 |
| $bc02 <$E> Error occurred while clearing the part's Offset results. | $bc02 <$E> 清出元件补尝值时发生错误 |
| $bc03 <$E> Attempted to use unsupported vacuum sensor. | $bc03 <$E> 尝试不使用真空感应器。 |
| $bc04 <$E> Error occurred while measuring the vacuum level. | $bc04 <$E> 真空测量发生错误。 |
| $bc05 <$E> Nozzle $N of head $H is clogged up. | $bc05 <$E> 喷嘴被阻塞在头中 |
| $bc06 <$E> The number of Mounting Data exceeds the maximum value. | $bc06 <$E> 贴装数据超过最大值 |
| $bc07 <$E> The number of Arrays exceeds the maximum value. | $bc07 <$E> 拼板数超过最大值 |
| $bc08 <$E> Attempted to use more axes than the maximum value. | $bc08 <$E> 尝试使用较多的 |
| $bc09 <$E> Attempted to use undefined dump stop option. | $bc09 <$E> 尝试使用的轴大于最大值 |
| $bc0a <$E> Attempted an undefined option which performs the ANC execution in advance. | $bc0a <$E> 试图使用未定义的抛料停止选项 |
| $bc0b <$E> Undefined option of Auto Limit Search Sequence exists. | $bc0b <$E> 自动极限搜索有不明确的选项存在。 |
| $bc10 <$E> Head is not in Home state. | $bc10 <$E> 头未回到原点 |
| $bc11 <$E> Mir is not in Home state. | $bc11 <$E> 镜子未回到原点 |
| $bc12 <$E> Can't use 'continue' function. | $bc12 <$E> 不能使用 '继续' 功能。 |
| $bd00 <$E> Unable to find the corresponding part information. | $bd00 <$E> 不能找对应的元件数据。 |
| $bd01 <$E> Unable to find the corresponding part's common information. | $bd01 <$E> 不能找到对应元件的公共的数据。 |
| $bd02 <$E> Unable to find the part information of LEAD type. | $bd02 <$E> 不能找到引脚类型的部份数据。 |
| $bd03 <$E> Unable to find the part information of BGA type. | $bd03 <$E> 不能找 BGA 类型的部份数据。 |
| $bd04 <$E> Unable to find the part information of CHIP type. | $bd04 <$E> 不能找CHIP类型的部份数据。 |
| $bd05 <$E> Unable to find the package information of a part. | $bd05 <$E> 不能找到相关元件的包装数据。 |
| $bd20 <$E> Unable to find the information about the corresponding fiducial mark. | $bd20 <$E> 不能找到基准点相关的数据 |
| $bd30 <$E> Unable to find the information about the corresponding nozzle. | $bd30 <$E> 不能找到与吸嘴相关的数据。 |
| $be00 <$E> Undefined Task ID. | $be00 <$E> 不明确的目标 |
| $be01 <$E> Attempted to execute incorrect sequence. | $be01 <$E> 尝试运行不正确的序列。 |
| $be20 <$E> Unable to find the Mount information. | $be20 <$E> 不能找到贴装数据。 |
| $be30 <$E> Attempted to place using the skipped head. | $be30 <$E> 尝试使用被跳过的头。 |
| $be40 <$E> Error occurred in calculating the Bad Mark position. | $be40 <$E> 在计算坏基准点位置时发生错误。 |
| $be41 <$E> Error occurred in calculating the Bad Mark position on the Guide. | $be41 <$E> 在计算坏基准点位置导向时发生错误。 |
| $be42 <$E> Error occurred in calculating the Accept Mark position. | $be42 <$E> 在计算可接收基准点位置时发生错误。 |
| $be50 <$E> Attempted to use an indefinable type of the Bad Mark position. | $be50 <$E> 尝试使用一个不能确定其类型的坏基准点位置。 |
| $be51 <$E> Attempted to measure the Bad Marks using the undefined device. | $be51 <$E> 尝试用不明确的方法来测量坏基准点 |
| $be52 <$E> Unable to identify any device for the recognition of Accept Marks. | $be52 <$E> 不能确定用何种方法来识别可接受基准点 |
| $be60 <$E> Error occurred in converting the logical coordinates to the Fiducial Camera position. | $be60 <$E> 在将逻辑坐标转换成基准照相机位置发生错误。 |
| $be61 <$E> Error occurred in converting the logical coordinates to the Head position. | $be61 <$E> 在将逻辑坐标转换成贴装头位置发生错误。 |
| $be70 <$E> Error occurred in computing the PCB Fiducial Mark position. | $be70 <$E> 在计算电路板基准点的位置时发生错误。 |
| $be71 <$E> Error occurred in computing the part's Fiducial Mark position. | $be71 <$E> 在计算元件基准点的位置时发生错误。 |
| $be72 <$E> Undefined type of Fiducial Mark for a part. | $be72 <$E> 不明确类型的元件基准点 |
| $be80 <$E> Undefined method of recognition for a PCB Fiducial Mark. | $be80 <$E> 不明确识别电路板基准点的方法。 |
| $be81 <$E> Attempted to use an undefined device for Fiducial Mark recognition. | $be81 <$E> 尝试应用不明确的识别基准点的方法 |
| $be90 <$E> Error occurred in computing the placement position. | $be90 <$E> 在计算贴装位置时发生错误。 |
| $bea0 <$E> Error occurred in computing the Upward camera position. | $bea0 <$E> 在计算向上照相机位置时发生错误。 |
| $bea1 <$E> Unable to identify any camera for an actual use. | $bea1 <$E> 不能识别哪个照相机是在实际使用。 |
| $beb0 <$E> Error occurred in computing the precedent Head in sequential Head operations. | $beb0 <$E> 在计算优先使用何头时发生错误 |
| $bec0 <$E> Attempted to recognize with the inadmissible angle value for the Vision. | $bec0 <$E> 尝试识别出可接受的图象角度值 |
| $bed0 <$E> Error occurred in configuring the part calibration data. | $bed0 <$E> 在配置元件校正数据时发生错误。 |
| $bee0 <$E> Unable to identify the camera number to recognize a component. | $bee0 <$E> 不能鉴别出识别元件的照相机序号 |
| $bef0 <$E> Attempted to use Upward Vision by means of Camera instead of Upward Camera. | $bef0 <$E> 尝试使用FIXCAMERA的相机图象 |
| $bef1 <$E> Attempted to use Fly Vision by means of Camera instead of Fly Camera. | $bef1 <$E> 尝试使用FLYING CAMERA的飞行视觉 |
| $bf00 <$E> Error detected in the sequence table of TskSch. | $bf00 <$E> 在检测任务表的进程时发生错误 |
| $bf01 <$E> Error detected in the scheduler table of TskSch. | $bf01 <$E> 在检测任务表的序列时发生错误 |
| $bf02 <$E> Error occurred in TskSch while executing the sequences. | $bf02 <$E> 在检测任务表的执行顺序时发生错误 |
| $bf03 <$E> TimeOut occurred in the sequence %d of TskSch. | $bf03 <$E> 在检测任务表的顺序时发生错误 |
| $bf10 <$E> Error detected in the sequence table of TskHead. | $bf10 <$E> 在检测执行头的序列时发生错误 |
| $bf11 <$E> Error detected in the scheduler table of TskHead. | $bf11 <$E> 在检测执行头的进程时发生错误 |
| $bf12 <$E> Error occurred in TskHead while executing the sequences. | $bf12 <$E> 在检测任务表的执行顺序时发生错误 |
| $bf20 <$E> Error detected in the sequence table of TskMir. | $bf20 <$E> 在检测TSKMIR的序列表时发生错误 |
| $bf21 <$E> Error detected in the scheduler table of TskMir. | $bf21 <$E> 在检测TSKMIR的进程表时发生错误 |
| $bf22 <$E> Error occurred in TskMir while executing the sequences. | $bf22 <$E> 在运行TSKMIR的序列时发生错误 |
| $bf30 <$E> Error detected in the sequence table of TskGan. | $bf30 <$E> 在检测TSKGAN的序列表时发生错误 |
| $bf31 <$E> Error detected in the scheduler table of TskGan. | $bf31 <$E> 在检测TSKGAN的进程表时发生错误 |
| $bf32 <$E> Error occurred in TskGan while executing the sequences. | $bf32 <$E> 在运行TSKGAN的序列时发生错误 |
| $bf80 <$E> Unable to browse the TskTray information. | $bf80 <$E> 不能浏览 TskTray 数据。 |
| $bfff <$E> Error occurred in Manual Command | $bfff <$E> 在人工的指令方面发生 错误 |
| $c000 <$E>Error occurred in configuring the acceleration/deceleration profile of $A. | $c000 <$E> 设置的元件库的加速/ 减速数据有错 |
| $c001 <$E> Error occurred in configuring the constant velocity profile of $A. | $c001 <$E> 设置的元件库的速度参数有错 |
| $c002 <$E> Error occurred in configuring $A's motion command. | $c002 <$E> 设置的元件库的移动指令有错 |
| $c003 <$E> Error occurred during the homing action of $A. | $c003 <$E> 回归原点有错 |
| $c004 <$E> Error occurred during the homing action of $A. | $c004 <$E> 回归原点有错 |
| $c005 <$E> Error occurred during $A's waiting for the Comp. | $c005 <$E> 等待过程中出错 |
| $c006 <$E> Negative S/W Limit detected in $A. | $c006 <$E> 负极限有错 |
| $c007 <$E> Positive S/W Limit detected in $A. | $c007 <$E> 正极限有错 |
| $c008 <$E> Incorrect scale factor detected during the calculation of coordinates. | $c008 <$E> 在坐标的计算期间发现不正确的比例系数。 |
| $c009 <$E> In the axis $A, in the middle of the system's waiting for a motion-end flag (%x), error %d occurred. | $c009 <$E> 在等待移动结束的信号时出错 |
| $c00a <$E> In the axis $A, in the middle of the system's configuring a motion-end flag (%x), error %d occurred. | $c00a <$E> 在设置等待移动结束的信号时出错 |
| $c00b <$E> Error occurred in accessing the axis board (X3203). | $c00b <$E> 控制板控制信号出错。 (X3203) |
| $c00c <$E> Manual operation should be performed after all the axes' homing action. | $c00c <$E> 回原点后才能手动操作 |
| $c00d <$E> Error occurred during the execution of automatic Limit search. | $c00d <$E> 自动搜寻极限发生错误。 |
| $c00e <$E> Current position of the Axis $A is NOT normal. | $c00e <$E> 轴位置不正常 |
| $c00f <$E> Axis $A TIME OUT ERROR Occurred. | $c00f <$E> 轴运动超时 |
| $c010 <$E> Fatal Following Error at the $A Axis. | $c010 <$E> 轴发生致严重的错误 |
| $c011 <$E> Invalid Axis Port Number detected. | $c011 <$E> 轴的通道数有错 |
| $c200 <$E> Invalid Index Offset Value in the Twin-servo axis. | $c200 <$E> 一对伺服轴的补偿值有错 |
| $c201 <$E> Timeout occurred during axis status check in the Servo Controller. | $c201 <$E> 在检测轴的伺服控制器的状时超时 |
| $c202 <$E> Mutex Timeout occurred in the Servo Controller. | $c202 <$E> 伺服控制器相对超时。 |
| $c203 <$E> Error occurred during the ASCII communication in the Servo Controller. | $c203 <$E> 伺服控制器在ASSII码通讯时发生错误。 |
| $c204 <$E> Handshake Error occurred in the Servo Controller. | $c204 <$E> 伺服控制器的握手指令发生。 |
| $c205 <$E> Mutex Integrity Error occurred in the Servo Controller. | $c205 <$E> 伺服控制器发生错误。 |
| $c206 <$E> Timeout occurred while waiting for the Motion Start. | $c206 <$E> 等待移动开始信号超时 |
| $c207 <$E> Invalid Home State detected in the Servo Controller. | $c207 <$E> 检测伺服控制器的原点状态有错 |
| $c208 <$E> Excessive Skew Error detected in the Twin-Servo axis. | $c208 <$E> 一对伺服轴不平行 |
| $c209 <$E> Excessive Full-Close Error detected in the X axis. | $c209 <$E> X 轴的控置全闭环错 |
| $c20a <$E> Excessive Full-Close Error detected in the Y1 axis. | $c20a <$E> Y1 轴的控置全闭环错 |
| $c20b <$E> Excessive Full-Close Error detected in the Y2 axis. | $c20b <$E> Y2 轴的全闭控制出错 |
| $c20c <$E> Failed to start the commanded motion in the Servo Controller. | $c20c <$E> 伺服控制器的开始移动指令有错 |
| $c20d <$E> Invalid Force Calibration Data Table. | $c20d <$E> 较正数据有错 |
| $c20e <$E> Invalid Force Control Command. | $c20e <$E> 控制命令有错 |
| $c20f <$E> Timeout occurred during the Force Control. | $c20f <$E> 压力控制超时 |
| $c210 <$E> Force Commmand Integrity Error. | $c210 <$E> 压力控制指令不完全 |
| $c211 <$E> Excessive load detected at Force Transducer. | $c211 <$E> 传感器检测超负荷 |
| $c212 <$E> Excessive Position Displacement detected during the Force Control. | $c212 <$E> 压力控制时移位 |
| $c213 <$E> Undesirable preliminary load detected before starting the Force control | $c213 <$E> 在压力控制之前，有不明原因的预负荷 |
| $c214 <$E> Detected too small displacement to complete the Force Control. | $c214 <$E> 完成压力控制时有佷小的位移。 |
| $c215 <$E> Servo Controller is retrying the motion that failed to complete previously. | $c215 <$E> 伺服控制器几经重试，对设定的运动仍无法完成 |
| $c216 <$E> Invalid Motion Profile Error. | $c216 <$E> 运动轨迹有错。 |
| $c217 <$E> One or more axes are in the Servo-Off state. | $c217 <$E> 一或较多的轴伺服关闭 |
| $c7ff <$E> Error occurred in motor actuation during the manual operation. | $c7ff <$E> 手动操作马达运动发生错误。 |
| $c800 <$E> CALC_MOUNT_POS_ERROR | $c800 <$E> 较正的贴装数据有错 |
| $c801 <$E> Configured as an undefined WaitPosition Type. | $c801 <$E> 设定了不明确的等待位置类型。 |
| $cfff <$E> Error occurred in the calculation results of coordinates. | $cfff <$E> 坐标的计算结果出错。 |
| $d102 <$E> TIME OUT occurred while DP-RAM Communication. | $d102 <$E> DPRAME 板通讯超时 |
| $e000 <$E> Access Fault occurred PC=%X, FA=%X, EA=%X. | $e000 <$E> 电脑通道访问出错 |
| $e001 <$E> Divide by Zero Error. | $e001 <$E> 复位错 |
| $e011 <$E> Access Fault occurred in Vision Board. | $e011 <$E> 图象板出错 |
| $e012 <$E> Access Fault occurred in IO CAN Board. | $e012 <$E> IO CAN BOARD 出错 |
| $e013 <$E> Access Fault occurred in DPRAM Board. | $e013 <$E> DPRAM 出错。 |
| $e014 <$E> Access Fault occurred in Axis 1 Board. | $e014 <$E> AXIS 1 板出错。 |
| $e015 <$E> Access Fault occurred in Axis 2 Board. | $e015 <$E> AXIS 2 板出错 |
| $e016 <$E> Access Fault occurred in Axis 3 Board. | $e016 <$E> AXIS 3 板出错 |
| $e017 <$E> Access Fault occurred in Axis 4 Board. | $e017 <$E> AXIS 4 板出错 |
| $e100 <$E> Error occurred in I/O Board %d (Error %x). | $e100 <$E> 错误发生在I/O %d.( 错误 %x) |
| $e101 <$E> Abnormality exists in the result of vision process. | $e101 <$E> 视觉程序的结果反常。 |
| $e200 <$E> No pneumatic pressure is being supplied. | $e200 <$E> 气压供应报警。 |
| $e300 <$E> Error occurred in $A axis. | $e300 <$E> 错误发生在 $A轴。 |
| $e800 <$E> Abnormal motor configurations in $A axis. | $e800 <$E> $A 轴马达异常。 |
| $e801 <$E> Unable to identify $A axis' velocity profile. | $e801 <$E> 不能识别$A轴速度变化。 |
| $e802 <$E> Unable to identify $A axis' Home Escape range. | $e802 <$E> 不能识别$A轴原点范围。 |
| $e803 <$E> Abnormal electric gear ratio in $A axis. | $e803 <$E> 电动牙箱齿数比异常。 |
| $e804 <$E> Unable to identify the scale of $A axis. | $e804 <$E> 不能识别$轴刻度 $轴。 |
| $e805 <$E> Unable to identify the safe position of $A axis. | $e805 <$E> 不能识别$A轴安全位置 。 |
| $e806 <$E> Attempted to identify unregistered feeder chink sensor. | $e806 <$E> 试图识别未注册感应器。 |
| $f800 <$E> While the system was creating QueueID %d, Error %d occurred. | $f800 <$E> 系统正在创造队列ID%d, 错误 %d 发生。 |
| $f801 <$E> While, To the Queue ID %d, message %d was being posted, Error %d occurred. | $f801 <$E> 当队列信息%d输出时, 错误 %d 发生。 |
| $f802 <$E> While a message was being pended at the Queue ID %d, Error %d occurred. | $f802 <$E> 当信息从队列发出未完成时 %d, 错误 %d 发生。 |
| $f803 <$E> While a message was being accepted from the Queue ID %d, Error %d occurred. | $f803 <$E> 当信息从对列读取%d时,错误 %d 发生。 |
| $f804 <$E> While the Queue ID %d was being created, Error %d occurred. | $f804 <$E> 虽然储列身份证 %d 正被产生, 错误 %d 发生。 |
| $f810 <$E> Error %d occurred in creating a flag. | $f810 <$E> 错误 %d 在建立标志时出现错误。 |
| $f811 <$E> In clearing the Flag %d, Error %d occurred. | $f811 <$E> 在清除标记%d时, 错误 %d 发生。 |
| $f812 <$E> At the Flag %d, in pending %x , Error %d occurred. | $f812 <$E> 在标记%d未完成,错误 %d 发生。 |
| $f813 <$E> In deleting the Flag %d, Error %d occurred. | $f813 <$E> 在删除%d时, 错误 %d 发生。 |
| $f814 <$E> While, to the Flag %d, the system was posting %x, Error %d occurred. | $f814 <$E> 当标记到%d,系统处理%x, 错误 %d 发生。 |
| $f820 <$E> Error occurred in creating the Semaphore %d. | $f820 <$E> 错误发生在建立标记信息 %d时。 |
| $f821 <$E> Error occurred in deleting the Semaphore %d. | $f821 <$E> 错误发生在删除标记信息 %d时 |
| $f822 <$E> Error occurred in pending at the Semaphore %d. | $f822 <$E> 错误发生在信息未处理 %d。 |
| $f823 <$E> Error occurred in posting at the Semaphore %d. | $f823 <$E> 错误发生在传递到信息 %d。 |
| $f900 <$E> Error %d occurred in creating the system memory. | $f900 <$E> 错误 %d 发生在创建系统存储器。 |
| $f901 <$E> Error %d occurred in deleting the system memory. | $f901 <$E> 错误 %d 发生在删除系统存储器。 |
| $f902 <$E> Error %d occurred in creating the PCB memory. | $f902 <$E> 错误 %d 发生在创建PCB存储器。 |
| $f903 <$E> Error %d occurred in deleting the PCB memory. | $f903 <$E> 错误 %d 发生在删除PCB存储器。 |
| $f910 <$E> System memory has not been created yet. | $f910 <$E> 系统存储器仍未建立。 |
| $f911 <$E> PCB memory has not been created yet. | $f911 <$E> PCB存储器仍未建立。 |
| $f912 <$E> Error %d occurred in PCB data structure. | $f912 <$E> 错误 %d发生在PCB数据构造中。 |
| $f920 <$E> Error %d occurred in allocating the Config DB memory. | $f920 <$E> 错误 %d发生在分配Config数据库存储器。 |
| $f921 <$E> Error %d occurred in allocating the Factory DB memory. | $f921 <$E> 错误 %d 发生在分配工厂数据库存储器。 |
| $f922 <$E> Error %d occurred in allocating the System DB memory. | $f922 <$E> 错误 %d 发生在分配系统数据库存储器。 |
| $fa00 <$E> Error %d occurred in allocating the Bad DB memory. | $fa00 <$E> 错误 %d 发生在分配不良数据库存储器。 |
| $fa01 <$E> Error %d occurred in allocating the Array DB memory. | $fa01 <$E> 错误 %d 发生在分配数组数据库存储器。 |
| $fa02 <$E> Error %d occurred in allocating the PCB Header memory. | $fa02 <$E> 错误 %d 发生在分配PCB标题数据库存储器。 |
| $fa03 <$E> Error %d occurred in allocating the AncDef DB memory. | $fa03 <$E> 错误 %d 发生在分配ANC定义数据库存储器 |
| $fa04 <$E> Error %d occurred in allocating the FidCon DB memory. | $fa04 <$E> 错误 %d 发生在分配FID定义数据库存储器 |
| $fa05 <$E> Error %d occurred in allocating the Mount DB memory. | $fa05 <$E> 错误 %d 发生在分配贴装定义数据库存储器 |
| $fa06 <$E> Error %d occurred in allocating the FidBeam memory. | $fa06 <$E> 错误 %d 发生在分配基准光点数据库存储器 |
| $fa07 <$E> Error %d occurred in allocating the FidSsaMath memory. | $fa07 <$E> 错误 %d 发生在分配基准数据库存储器 |
| $fa08 <$E> Error %d occurred in allocating the Tape Feeder DB memory. | $fa08 <$E> 错误 %d 发生在分配带式喂料器数据库存储器 |
| $fa09 <$E> Error %d occurred in allocating the Stick Feeder DB memory. | $fa09 <$E> 错误 %d 发生在分配杆式喂料器数据库存储器 |
| $fa0a <$E> Error %d occurred in allocating the Tray Feeder DB memory. | $fa0a <$E> 错误 %d 发生在分配盘式喂料器数据库存储器 |
| $fa0b <$E> Error %d occurred in allocating the Part DB memory. | $fa0b <$E> 错误 %d 发生在分配元件数据库存储器 |
| $fa0c <$E> Error %d occurred in allocating the PackCom DB memory. | $fa0c <$E> 错误 %d 发生在分配PACKCOM数据库存储器 |
| $fa0d <$E> Error %d occurred in allocating the PackSsaLl DB memory. | $fa0d <$E> 错误 %d 发生在分配PACKSSALI数据库存储器 |
| $fa0e <$E> Error %d occurred in allocating the PackSsaBga DB memory. | $fa0e <$E> 错误 %d 发生在分配PACKSSBGA数据库存储器 |
| $fa0f <$E> Error %d occurred in allocating the PackSsaChip DB memory. | $fa0f <$E> 错误 %d 发生在分配PACKSSACHIP数据库存储器 |
| $fa10 <$E> Error %d occurred in allocating the PackChuck DB memory. | $fa10 <$E> 错误 %d 发生在分配PACKCHUCK数据库存储器 |
| $fa11 <$E> Error %d occurred in allocating the PackCa DB memory. | $fa11 <$E> 错误 %d 发生在分配PACKCA数据库存储器 |
| $fa12 <$E> Error %d occurred in allocating the PackQa DB memory. | $fa12 <$E> 错误 %d 发生在分配PACKQA数据库存储器 |
| $fa80 <$E> Error %d occurred in allocating the Bad Real DB memory. | $fa80 <$E> 错误 %d 发生在分配BAD REAL数据库存储器 |
| $fa81 <$E> Error %d occurred in allocating the Array Real DB memory. | $fa81 <$E> 错误 %d 发生在分配ARRAY REAL数据库存储器 |
| $fa82 <$E> Error %d occurred in allocating the PCB Header Real DB memory. | $fa82 <$E> 错误 %d 发生在分配PCB HEADER REAL数据库存储器 |
| $fa83 <$E> Error %d occurred in allocating the Mount Real DB memory. | $fa83 <$E> 错误 %d 发生在分配MOUNT REAL数据库存储器 |
| $fa84 <$E> Error %d occurred in allocating the CycleEntryReal DB memory. | $fa84 <$E> 错误 %d 发生在分配CYCLEENTRY REAL数据库存储器 |
| $fa85 <$E> Error %d occurred in allocating the Tape Feeder Real DB memory. | $fa85 <$E> 错误 %d 发生在分配带式喂料器实时数据库存储器 |
| $fa86 Safe G Error %d occurred in allocating the Stick Feeder Real DB memory. | $fa86 <$E> 错误 %d 发生在分配杆式喂料器实时数据库存储器 |
| $fa87 <$E> Error %d occurred in allocating the Tray Feeder Real DB memory. | $fa87 <$E> 错误 %d 发生在分配盘式喂料器实时数据库存储器 |
| $fa88 <$E> Error %d occurred in allocating the PackReal DB memory. | $fa88 <$E> 错误 %d 发生在分配PACKREAL数据库存储器 |
| $fa89 <$E> Error %d occurred in allocating the Head Real DB memory. | $fa89 <$E> 错误 %d 发生在分配HEAD REAL数据库存储器 |
| $fa8a <$E> Error %d occurred in allocating the AncDef Real DB memory. | $fa8a <$E> 错误 %d 发生在分配ANC定义实时数据库存储器 |
| $fa8b <$E> Error %d occurred in allocating the Product Real DB memory. | $fa8b <$E> 错误 %d 发生在分配PRODUCT REAL数据库存储器 |
| $fb00 <$E> Error %d occurred in releasing the Bad DB memory. | $fb00 <$E> 错误 %d 发生在释放不良数据库存储器。 |
| $fb01 <$E> Error %d occurred in releasing the Array DB memory. | $fb01 <$E> 错误 %d 发生在释放数组数据库存储器。 |
| $fb02 <$E> Error %d occurred in releasing the PcbHeader DB memory. | $fb02 <$E> 错误 %d 发生在释放PCB标题数据库存储器。 |
| $fb03 <$E> Error %d occurred in releasing the AncDef DB memory. | $fb03 <$E> 错误 %d 发生在释放ANC定义数据库存储器 |
| $fb04 <$E> Error %d occurred in releasing the FidCon DB memory. | $fb04 <$E> 错误 %d 发生在释放FID定义数据库存储器 |
| $fb05 <$E> Error %d occurred in releasing the Mount DB memory. | $fb05 <$E> 错误 %d 发生在释放贴装定义数据库存储器 |
| $fb06 <$E> Error %d occurred in releasing the FidBeam DB memory. | $fb06 <$E> 错误 %d 发生在释放基准光点数据库存储器 |
| $fb07 <$E> Error %d occurred in releasing the FidSsaMath DB memory. | $fb07 <$E> 错误 %d 发生在释放基准数据库存储器 |
| $fb08 <$E> Error %d occurred in releasing the Tape Feeder DB memory. | $fb08 <$E> 错误 %d 发生在释放带式喂料器数据库存储器 |
| $fb09 <$E> Error %d occurred in releasing the Stick Feeder DB memory. | $fb09 <$E> 错误 %d 发生在释放杆式喂料器数据库存储器 |
| $fb0a <$E> Error %d occurred in releasing the Tray Feeder DB memory. | $fb0a <$E> 错误 %d 发生在释放盘式喂料器数据库存储器 |
| $fb0b <$E> Error %d occurred in releasing the Part DB memory. | $fb0b <$E> 错误 %d 发生在释放元件数据库存储器 |
| $fb0c <$E> Error %d occurred in releasing the PackCom DB memory. | $fb0c <$E> 错误 %d 发生在释放PACKCOM数据库存储器 |
| $fb0d <$E> Error %d occurred in releasing the PackSsaLl DB memory. | $fb0d <$E> 错误 %d 发生在释放PACKSSALI数据库存储器 |
| $fb0e <$E> Error %d occurred in releasing the PackSsaBga DB memory. | $fb0e <$E> 错误 %d 发生在释放PACKSSBGA数据库存储器 |
| $fb0f <$E> Error %d occurred in releasing the PackSsaChip DB memory. | $fb0f <$E> 错误 %d 发生在释放PACKSSACHIP数据库存储器 |
| $fb10 <$E> Error %d occurred in releasing the PackChuck DB memory. | $fb10 <$E> 错误 %d 发生在释放PACKCHUCK数据库存储器 |
| $fb11 <$E> Error %d occurred in releasing the PackCa DB memory. | $fb11 <$E> 错误 %d 发生在释放PACKCA数据库存储器 |
| $fb12 <$E> Error %d occurred in releasing the PackQa DB memory. | $fb12 <$E> 错误 %d 发生在释放PACKQA数据库存储器 |
| $fb13 <$E> Overlapped Vision Command Exist ! | $fb13 <$E> 叠加视觉指令存在 ! |
| $fb14 <$E> Vision Response Exceed VME Defined Time Out . | $fb14 <$E> 视觉响应超过VME定义时间外。 |
| $fb21 <$E> Detect Over Heat Sensor inside Machine. | $fb21 <$E> 检测出内部温度超温。 |
| $fb24 <$E> Safe Guard On | $fb24 <$E> 安全保护开 |
| $fb25 <$E> Safe Guard Off | $fb25 <$E> 安全保护关 |
/1 
窥视卡
雷达卡
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
千斤顶
显身卡
楼主